79072312015 Kenmore Range - Instructions

Repair was quite easy, as long as you have the instructions for removing the door. The screws that hold the bottom of the door to the fixed hinge are placed into the side of the hinge assembly after removal; this holds the door at a 45 degree angle for easy removal. After that, just place the door on a flat surface and dismantle the door from the inside. The inner glass is contained in a metal frame with another piece of glass; this frame comes apart easily using the clips in each side. The door assembles easily after the glass is replaced; just take your time and give yourself enough room to lay out the parts as you go. Good luck!

Turned power off at electrical panel. Pulled oven away from wall. Removed back cover (6 screws), then unplugged wires from old receptacle. I had to pull the squeeze clips backwards & break them to remove the old receptacle - couldn't squeeze them enough to remove them otherwise. The old receptacle came out through the inside of the oven, and the new one snapped in easily from inside the oven as well. Replaced wiring, installed new bulb, restored power & tested. Replaced back cover. Good time to vacuum under/behind where the oven usually lives before sliding it back to the wall.

Replaced the probe because that's what this site recommended.The oven still does not heat up.

took off back cover and unplugged old unit and installed new unit. oven probe was not the issue. probally control panel malfunction of readings. will continue using oven temperatue gauge inside to get settings for temperture as temp is important for baking.

I was selling my home and did not realize that the anti-tip bracket was not originally installed. A home inspection caught the problem and the buyers required that I install one. I could not find the original and obviously the installer never put it in place to begin with. The buyers wanted this resolved within a week so I had to act fast. I could not find one locally so I found what I needed on your website. It arrived in a couple of days and was easy to install. I used the template provided in the kit and drove the screws through the bracket into the wood plate behind the drywall. Pushed the range back in place and that's it. Couldn't get any easier.

First, remove the warming drawer. This allows access to the igniter's plug. Unplug the igniter. The rest of the job is performed within the oven. Remove the bottom (1/4 inch socket). Then remove the next, v shaped piece. The igniter is bolted to the aerator. Remove bolts, and it pulls right off. Reverse these to install new igniter.

Had to reference original owner's manual for instruction(s) on how to remove oven door. Used several "YouTube" videos to reference oven door design (Oven door glass is actually several layers of glass.) After completing about 30 mins of research and finding the right square drive bit, the repair went smoothly and without complications. The biggest challenge was researching and understanding what part(s) were needed and how to replace them. It seemed liked a lot of work doing the research however it sure beat a $350 repair bill. It cost me $90 and about 1 1/2 hours of total time. Oven works better than ever, thanks parts select for the part(s) and diagram(s) ...

Turned off electric,removed rear panel and replaced part.oven is now operating good as new.

Remove 4 screws on back panel. Unclip wire connector and remove probe and install new probe.

I opened the door of the gas range and slid the rack in. No one can do this! I am amazing.

First I removed the two screws that hold the bottom panel I then pulled the panel out and put the new panle in and put the two screws back in

move the range out and unplug power supply, removing the back cover allows access to the probe, this can be done with screw driver or nut driver, loosen clamp that holds power cord in place and move backing out of the way, be careful sheet metal can be sharp, locate the probe unplug the connector and remove screw holding probe, pull old probe out install new probe, fasten down and plug in connector. attach backing and tighten clamp on power cord, plug in to power supply, turn on oven and give it several minutes for probe to work, it took only 20 minutes to replace the bad probe and the oven works like new hop this helps

This was the first time replacing the fan. It is a lot easier to work in the oven compartment with the oven door removed, only two screws on the door and the hinges were released. I found that a couple of the screws were either rusted or stripped so I used a pair of pliers to remove the screws that were holding the diffuser in place. Once there was access to the fan I found that the fan was warped and that the blades were scraping against the back wall of the oven. The next challenge was to remove the retaining nut. I used a sheet metal screw to secure the warped fan to keep it from spinning. once I figured out that you have to turn the retaining nut to the right to loosen, it came off easily. 1/2" socket with extension. When I replace the fan I used two washers for spacers to make sure that the fan would not scrape the wall of the oven. Its been tested many times and the oven does not make that horrible sound anymore.

Oven ignitor is on the bottom gas unit. Ignitor is in oven and plug is in warmer oven on left wall at very back of warmer oven. It has duel function to light both upper and lower gas burners (in oven). Wires of new plug that I received were shorter than existing wires and would not reach the plug from ignitors center mount location to plug at far back of warming unit on left wall. Even if the wires would have been long enough, I couldn't figure out how to "release" the existing plug. Easy solution: Cut old wires at junction of old ignitor (leaving wires as long as possible). Cut new wired as close to new male plug as possible (leaving wires as long as possible on new ignitor). Strip ends of old and new wires and wire nut with porcelin wire nuts (hardest part of job was locating porcelin wire nuts)! After placing wires out of the way of burner and ignitor, reassemble stove parts. AVOID touching new element as oil from hands will decrease the life of the element. Good Luck..

Tore the oven apart and replaced the igniter, then put the oven back together. Perhaps if Frigidaire manufactured an appliance that lasted longer than three years this wouldn't have been necessary. This is the second Frigidaire range that only lasted three years. Believe, the next stove we buy will definitely not be a Fridgidaire!