79015032500 Kenmore Wall Oven - Instructions

Cut off power at fuse panel. pulled stove out from wall went behind stove removed back panels in area of sensor that I could see from the front side, inside oven. Located sensor from rear & unpluged senser from wiring bundle reached inside oven & removed screws from sensor. Pulled sensor out & threaded wire through hole. Took old & new sensors to bench in shop. Plug on new not the same as old. Had to change plug Cut and stripped wires. Wire is very small, need to use a good stripper. Twisted wire together & soldered connection, used shrink wrap to insulate wire. Took part inside and reinstalled in reverse order. Used 1/4 inch nutdriver on total job start to finish.

First we removed two screws under the rim of the range top to open the lid. Lifted the lid and removed the screws from the bracket that holds the elements, Be careful with the clips that hold the element in, if you break them or bend them there aren't any more! Also note which holes they were in, they are marked according to the different sizes of elements. Disconnected the wires, needed needlenose pliers to grip them...connected new element, popped it back in place, replaced bracket, closed top ...Easy peasy!!!

I called a repair place. They charged $54 to diagnose, (said it needed a new latch motor) then wanted $220 to complete the repair. I checked online prices and did it myself for about 15 minutes work and the latch motor itself ($44?).

Was necessary to uplug the range, pull it away from the wall and remove the back panel sheet metal, then 3 screws that mount the motor. Replace motor, reattach sheet metal. Plug in. Done. Ready to bake cookies.

Started by replacing element which was clearly broken. Still no heat. So then I changed the oven sensor. Was disappointed that when I received the sensor I had to cut and splice the connector that was on it with the old one that came off the old sensor. Did that and still no heat so I had to buy a new clock/timer. Went to another store for that because of the connector not being the right type and there was no picture of the clock/timer like the other website. Overall ok, normall troubleshooting steps, just wish I didn't have to cut and splice the connector on the new sensor I purchased from here.

Sensor very accessible. Pull off the back panel, disconect the sensor and slide out from back of oven. The original plug was cut off the sensor, as well as the new one to get the proper connector type on the new sensor. Soldered and heat shrink, and presto we had our new sensor ready for install. Install was about 5 minutes which included putting the back panel on the range. Pretty easy and works like new. Total time for project was about 20 minutes.

I couldn't unscrew the leveling foot because it was rusted and corroded. The bracket holding it was easy to remove so I took the bracket with the corroded foot off and replaced it with the new foot and bracket. Very simple. I made sure I oiled it so it wouldn't rust again.

removed the old burner and put the new one in it's place.

My husband followed the video instructions and it was easy to fix.

We removed the old part and replaced it then when warming the oven all of a sudden there was a loud noise and something went and so we called a repair man which I guess we should of done in the first place. Now he has ordered a part that cost 170 soo that is my story don't try to repair if you don't have experience.

Screw the handle, that it...

New ones fit perfectly. Take a minute to bend the frame straight. Then and I used oversize screws on the replacement parts as the drop had stripped out the screw holes of the frame.

I wanted the bracket for the oven heating element and received the bracket for the broiler.... part returned and now I am stumped about what my next move will be

Watched a video - piece of cake!

1. Order part
2. Remove 2 top screws holding vent cover and carefully remove
cover
3. Open door all the way and lift, door will come of the microwave
4. Set door on a flat surface facing down
5. You will need a flat screwdriver,carefully set the screwdriver
between the door and the black plastic and pry out completely
6. Remove screws holding handle. (This will be a good time to clean
the inside of this door)
7. Attach new handle tighten screws
8. Put black plastic back in door and press on all around make sure
that is set in place
9. Re-install door and vent.

remove back panel took out old part splice wire replaced