Models > 74077 > Instructions

74077 LG Refrigerator - Instructions

All Instructions for the 74077
1 - 15 of 15
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Ice chute would not open.
Removed ice dispenser and display with small screwdriver from front of the fridge. Pried out the whole piece slowly. This exposed the motor that activates the chute. Plugged in the new motor before any removal to verify the motor was the problem. When it worked, removed old and installed new. 3 screws. Piece of cake.
Parts Used:
MOTOR,DC
  • Steve from MUKWONAGO, WI
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
11 of 23 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Ice Maker Quit Making Ice
For this model the ice maker is very easy to replace. All it takes is a phillips head screwdriver. There are two wire connections you have to unplug. Easy out easy in. You do not have to disconnect the water line, just make sure the line is lined up correctly when you reinstall the new icemaker. It seems to take approximately 8 hours before you start getting ice again. If you have this same model, you already know this ice maker is very slow in making ice and is not able to keep up with daily usage of ice for a household of 3.
Parts Used:
Refrigerator Ice Maker
  • Jeff from HUMBLE, TX
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Glass shelf broke during cleaning
Very easy. Just slipped it back into place
Parts Used:
Glass Shelf
  • Barbara from HAMILTON, NJ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Ordering the right parts
I ordered the needed parts, the correct ones I thought, but when they arrived, I realized they were the wrong parts shipped to me. The reason the wrong parts were shipped to me was because PartsSelect failed to advise me there were none of the parts I needed available so they shipped the left hand basket assembly, door, versus the desired right hand basket assembly, door. I then had to return the wrong parts shipped to me, at my cost of ~$25, and await a refund for the wrong parts originally shipped to me. That's how I did the repair.
Parts Used:
BASKET ASSEMBLY,DOOR
  • Kip from RICHMOND, VA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
4 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Ice maker stopped working
The Ice Maker from Part Select was complete. Plastic housing, Ice maker located at the top and ice cruncher/dispenser at the bottom.
Note: Both the ice maker and the dispenser wiring goes to a common connecter. It is not advisable to plan changing out only one of these.
Parts Used:
Ice Maker and Auger Motor Assembly
  • Orlando from MESA, AZ
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door stopper broke
Installed new door stopper with screw driver on bottom of french door
Parts Used:
STOPPER,DOOR
  • ROGER from SCHELLSBURG, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Intermittent ice flow
Very Intuitive.
Removed ice cube holder.
Removed all visible screws or fasteners paying attention to size, length and location.
With wiring and connectors exposed, I disconnected those and was now ready to install new ice maker in reverse order.
Once reassembled it took approximately 2 hrs to start making ice.
I found part installation to be really quiet easy.
Parts Used:
Refrigerator Ice Maker
  • Chris from CAMP HILL, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Ice Maker Stopped Working
Removed screws from broken Multi Ducts, pulled broken pieces from ice maker and replaced new Multi Ducts.
Parts Used:
DUCT,MULTI DUCT,MULTI
  • Keith from YORKTOWN, VA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
My glass shelf shattered after I had taken it out to clean it
Inserted the new shelf
Parts Used:
Glass Shelf
  • Rachel from SAN MATEO, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken door basket
The repair was an easy replacement. The problem was the LG part was no longer available from LG or any of the other places I tried. The PartSelect customer service representative was a true professional and did an outstanding job of helping find the correct part (LG's diagram was unreadable) and cross-referenced it to find the the part that PartSelect actually had in stock. I had the part in four day. The best customer service I have had in years. I lost his name but the order was 13449146. He deserves a raise!
Parts Used:
BASKET ASSEMBLY,DOOR
  • William from LARGO, FL
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water/ice maker not working
Remove push plate for water/ice maker switch, remove 2 screws and 2 wires for switch. Replace with new.
Parts Used:
Switch,Micro
  • Brent from ROGERS, MN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
6 of 17 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Ice maker compartment icing
Remove 3 screws bottom and base.
Loosen top screw. Pull out from bottome and unplug wire harness.
Parts Used:
Ice Maker and Auger Motor Assembly Refrigerator Ice Container Assembly
  • Jerry from RIDGEFIELD, NJ
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
replace hand screw
unfortunately my fridge stopped working. I purchased another but wanted to try and repair the old one. when ew one arrived, the old one was supposed to be put in garage but instead was hauled away. Had delivery return next day but they had as already removed and lost the handle screw for the bottom freezer and the screw that holds handle in place. ordered the handle screw and picked up the nut. very simple to install the screw and put handle back on.
Parts Used:
Handle Screw
  • dorothy from SALISBURY, MD
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Frost in the freezer. Icemaker frozen.
I called LG and followed the instructions given over the phone. The instructions couldn't have been simpler. Disconnect the appliance for several hours and then connect again. I disconnected the appliance overnight, cleaned out the freezer, and reconnected it. Problem solved. Did not need to call a repairman and did not use the clips.
Parts Used:
Clip
  • Teresa from Miami, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    More than 2 hours
1 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
plastic tube leaking at connector
Uncoupled the old connector, replaced with new connector and attached supply line. Repair easy with right part, prior to ordering the right part I had tried a compression fitting and it still leaked. U-tube and others demonstrating repair assured me I was on the right path.
Parts Used:
Holder,Bracket
  • GREG from STILLWATER, NJ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Wrench (Adjustable)
1 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 74077
1 - 15 of 15