72373 LG Refrigerator - Instructions

Shut off water supply. Disconnect main supply line. Remove rear lower panel on back of refrigerator. Remove all tubing clamps on back. Disconnect leaking tubing from water supply valve. Remove water filter and unscrew/remove water filter housing. Replace tubing - connect to water filter housing then to water supply valve. Reconnect filter housing and filter. Reinstall lower panel, then main water supply line, then all tubing clamps. Turn water back on and check for leaks after discarding several glasses of water to fill filter. Job complete!

An easy way to get a refrigerator out from the wall is to use a tow strap or 1/2 to 3/4 in. rope. Throw a loop behind refer while keeping both ends in your hands. Let it settle down to the lower half of unit and pull using both hands. Comes right out.
Remove lower panel. Unscrew water valve from cabinet. Remove all tube holders Lay some rags down to catch a little water drainage.
Turn off water supply valve at wall. Unplug Power. Remove filter and filter holder. (one screw).
remove tube from valve by removing plastic C clip. Push plastic ring towards the valve and pull out tube at same time.
With the tube free, remove filter, then mount screw to remove the inside filter holder. When it is out, pull the tube doing the same process as the lower end. Pull tube out and replace with new one putting everything back in reverse order.
Before placing tube holders back on, turn on water to check for leaks.
After turning water back on and plugging in power, push refer back into place.
While I was there, I also replaced the hose from the wall to the refer.

Removed ice dispenser and display with small screwdriver from front of the fridge. Pried out the whole piece slowly. This exposed the motor that activates the chute. Plugged in the new motor before any removal to verify the motor was the problem. When it worked, removed old and installed new. 3 screws. Piece of cake.

Removed old filter head, installed the new head

I installed the new 3 wire ice maker very easily, but it was defective. I was told that instructions for the return of the defective part would be sent later due to the virus. I have never received the return instruction.
I did receive a credit for the defective part. VERY Satisfied with y’all’s service.
Waiting for return instructions if y’all still want it back.
Thanks,
Thomas Pennebaker

The heavy work is moving the fridge, then take off the lower plans. Use a bowel or cup for screws and the water line connector spacers so you don't loos them.
undo connections holding water line, including the bottom brakes for the solenoid. Reuse the spring around the lower waterline to prevent external wear on the line.

NOTE: remove the waterline connector spacers and save!
NOTE: you must compress (not pull) the connect to then pull the waterline out of the connectors.
NOTE: You must also remove the water filter and housing inside the fridge but this is easy.
MOTE: Test the line for leaks by turning on the water and then using the door water. The filter will need to refill so it may take a minute before water comes up. This line only have pressure when the door water is used or the ice maker needs to make ice.


After replacing the line, test the line for leaks by using the door water so the solenoid fills the lines

Part Select had a great video which made the repair easy, using a putty knife to start removing the freeze door gasket. Once removed the install is simple just snap the new gasket into the track, but start at the corner. Other company's have a video requiring you to remove the entire freezer compartment out of the appliance, unnecessary waste of time and labor.

Once I U tubed the the removal and replacement of the gaskets it was super easy. The right gasket change was easy without tools. The left gasket required me to remove the mullion first, which is why I used Utube.

I actually watched a YouTube video for LG refrigerators. The hardest part was taking the wire harness out. Mine was really stuck in there. But got it, put the new switch in and viola it worked. Yay!

I ordered the needed parts, the correct ones I thought, but when they arrived, I realized they were the wrong parts shipped to me. The reason the wrong parts were shipped to me was because PartsSelect failed to advise me there were none of the parts I needed available so they shipped the left hand basket assembly, door, versus the desired right hand basket assembly, door. I then had to return the wrong parts shipped to me, at my cost of ~$25, and await a refund for the wrong parts originally shipped to me. That's how I did the repair.

Replaced old hose and installed the new one. Was very simple with the instructions in your email..... step by step, could not of been any similar.... you guys rock

Simply removed old gasket. Started in a corner with installing the new gasket. It went in easily and quickly.

Watched a couple of YouTube videos and then went at it

Installed new door stopper with screw driver on bottom of french door

The repair was an easy replacement. The problem was the LG part was no longer available from LG or any of the other places I tried. The PartSelect customer service representative was a true professional and did an outstanding job of helping find the correct part (LG's diagram was unreadable) and cross-referenced it to find the the part that PartSelect actually had in stock. I had the part in four day. The best customer service I have had in years. I lost his name but the order was 13449146. He deserves a raise!