66562619300 Kenmore Microwave - Instructions

I ordered the part according to the Model number, inserted the part very easily, (and I am soooo challenged in that area) and now it turns again. :)

This is not easy to do. I done it before to replace a broken window and it was a real bitch. I considered buying a new door rather then do it again.All I wanted to do was tighten two screws that hold the handle.
I used the advice found on your web site from a person who did it using quarters and putty knifes to remove the choke and the door insert. Sounded silly but it works like a charm. I advise anyone who needs to do this repair to use that info on your web site. It will save lots of frustration. Be sure to have plenty of quarters and a few pennies.

replace one of the four rack supports which was melting

I turned off the power to the oven at the breaker. I then removed the side trim pieces by removing the screws located behind the lower oven door. I removed the plastic trim pieces above and below the microwave oven and removed the control panel and slid it into the opening above the microwave. I located the two screws securing the microwave into the frame and began sliding it out. I had to disconnect a small wiring harness and two wires from the microwave that were attached inside the opening above the microwave. The microwave section was the easily slid out, turned on it's side where the turntable motor was accessed by removing the access panel. I pulled the old motor, checked resistance and it matched the new motor. I then checked the old motor by applying 120V to it and it ran FINE! I thought I had the wrong part, but decided to install the new motor anyway. I did, secured the access panel and replaced the microwave in the frame. I reconnected the wires and secured the control panel and tested the microwave...and the turntable works!

Replaced bulb by: 1 pulling plug on microwave to make sure not hot - no power; 2 used needle nose pliers with head part about same size that fit inside of socket; 3 opened pliers and held firm against broken metal part; keeping pressure of pliers against broken metal part of light bulb, slowly unscrewed the broken part from socket using firmly held opened pliers. The rest was a cinch...just screwed in new light bulb, plugged in microwave and viola - there was light once again.

I used a Google search to show how to access the area behind the front panel. There was a folded paper copy with a schematic and wiring diagram in that space.Then I used a multi-meter to determine which of the THREE micro-switches was causing the problem. I called your help line and ordered a replacement switch. The switch was delayed in transit so your agent credited me with the cost of shipping.

When the part arrived, it had three terminals instead of two as shown in the on-line picture but that did not cause any difficulty in using it. It took about 20 minutes to remove and replace the old switch.

All seems to be working well now.

Finding which of the THREE switches was the problem was the most difficult part of the repair. All three "clicked" but the defective one did not click as easily. It needed to be depressed more than the door latch can would provide. Old age?

removed the two screws, removed all of the broken tab pieces, replaced with new grill, put the two screws back.,....DONE Easy as pie

After reading other entries, I have determined this is a problem with most grills on the whirlpool microwaves. Defective material ..becomes brittle and crumbles.

Removed screws holding the broken grill tabs with a phillips screwdriver
Removed broken grill and all broken tabs that fell into the vent area
Cleaned area where the new grill was to be placed
Inserted new grill onto the appropriate tabs and tightened the screws

BE CAREFUL as the tabs on the grill are thin and fragile when you insert the new grill don't force it into the slots, I used a knife as a way to slide the grill into place.

It was a bit awkward because the microwave is mounted over my stove. I had to twist around and install the bulb and then replace the cover. It was a bit uncomfortable. It took me about 10 minutes to complete.

Piece of cake. One screw to release the dropdown light diffuser. Just remember, the you're screwing the new bulb in from a reverse perspective. Also this site sends the correct part the first time.

Take off top facing over microwave using screwdriver also protection plate for diode and capaitor. Disconnect diode from frame, bracket to capacitor then remove, disconnect wires leaving diode on capacitor for right connection, replace, rewire done.

Removed 2 screws from top of microwave. Place new grill in place. Replaced 2 screws that were removed. What was wonderful is I ordered the part around 3 pm on a Friday. The part arrived at 9AM the next day and that was without requesting special shipment.

Unscrewed the remaining pieces of bracket slipped in new vent cover and attached with the two screws. Very easy since the web site showed where the vent attached. I saved over $60.00 doing this repair myself!

I removed the two screws and took off the old grill. Snapped the new grill in place and replaced the screws. This model was not shown on the list but the part fit just fine. The part arrived in 2 days! I ordered the white one and at first didn't think it matched .. maybe my microwave was bisque or almond .. but after 15 minutes of scrubbing I realized it was white but just real dirty .. lol. Now the door opens without the grill falling off. Easy fix.

I didn't have to remove the old cover since it cracked and fell off the microwave already. I simply snapped in the new vent cover, screwed in the 2 screws and I was done. Super easy.