The rubber washer is a part which is specific to dishwashers and should not be substituted by a similar part. It works with the heating element to seal the receptacle opening where the heating element...
The dishwasher lid spring helps open the dispenser cover in the soap box when the control releases the latch. If your dishwasher does not dispense detergent, is broken and worn out, or the door is not...
The faucet adapter for your portable dishwasher or washing machine attaches to the faucet and allows you to connect the machine to the tap. Before you install the faucet adapter on your taps, be sure ...
This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air conditioners. This ...
This cap does not require the use of an O-ring seal. The wet agent assembly cap is clear in color and made of plastic. This is a part for your dishwasher. This part may need to be replaced if you noti...
The lid hinge pin or detergent lid pin on your dishwasher helps dispense your dish detergent when your dishwasher is running. The pin fits with the dispenser lid and allows the lid to pop open and dis...
This soap cup latch kit, used in a dishwasher, will keep the dispenser cover closed. If your dishwasher will not dispense detergent, there is a door latch failure, the dishes are not cleaning properly...
This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, or microwaves. It is...
The first thing I did was to investigate. I needed to find where the leak was coming from. It was leaking from just above tne door front panel, directly underneath the control panel buttons. I opened the dishwasher door, and decided to remove the door screen vent. I was covered with some offwhite fiberous, or filter like material. I thou
... Read moreght perhaps the filter had broken down, and I ordered a new screen. When it arrived, and, although I had expected to receive a new filter with the plastic door screen, I didn't. There wasn't one to be ordered. I looked at the screen again. My problem was, that although I had considered that the substance I had thought was a filter, was instead build up of detergent, and other particals. That idea didn't seem to make sense. I didn't think it was possible for that stuff to get to the door screen. I thought, it was too far away from the dispenser and food particles. As it turned out, the buildup was, in fact, the problem. I properly cleaned the door vent, which was then fine, and I put it back into the door. There were no more leaks, that was it, and the problem was solved. As a last note however, unfortunatley, I have to return the new door vent screen that I ordered. I enjoyed solving the problem, and you all helped alot. Let's do it again sometime.
First, examine very carefully how the old spring relates to the detergent release box lid. Note that the top of the spring has a square-end upside down "U" . This rests on a small ledge on the detergent box. Also note that on either end of the spring is a straight extension of the spring wire. These two "legs" must rest on the inside o
... Read moref the edge of the detergent box. Second, use a flat blade screw driver to pry the LID hinge pin from the mounting "posts. Remove the pin, first noting the position of the spring. Reassemble the spring on the hinge pin in reverse order. Then snap the lid onto the spring using the two mounting "posts". NOTE: I used a very fine needle nose pliers to move the two spring "legs" behind the detergent box edge after I had mounted the lid. Flip the lid down to test if the spring pressure on the lid can be felt. Harold Kitzmann, Fishersville VA
After determining that the leak was coming basically from the motor shaft I googled until I thought I could handle it, took it apart to confirm I could get it apart (I thought it might be too stuck and I might need the whole motor thing) and then ordered the kit.
I don't think this could be done with the dishwasher in place, so
... Read more I turned the water off to the unit and unplugged it. I had previously removed the front bottom cover plates (4 screws). I opened the front, removed the lower dish rack and unscrewed it from the bottom side of the counter, disconnected the water supply and drain line, then wiggled it out being careful of the insulation sheets, hoses, etc. Note, water drains everywhere. I had some baking pans to contain and paper towels to wipe but still, be safe / prepared.
I disconnected everything from the motor / impeller housing area, then went inside the unit and loosened the lock ring thing around the base of whatever you call the spinning arm / sprayer, it took a little effort, might be easier to try this when it is still mounted to the counter. After that main ring was removed the housing with the motor and everything just wiggled free.
I unscrewed the motor's 3 Torx screws, and then the unscrewed the plastic "X" at the end opposite the motor, the brass weight pulls straight off and the impeller is supposed to come off too. Mine was stuck like many I read about. I drilled a hole in the end of the plastic impeller and drove the motor shaft out with a punch and hammer, it worked pretty slick. Then I carefully pried out the last seal and stopped for a cold beverage, major success.
I carefully pushed the new seal into the housing, reattached the motor to the housing, pushed on the other new seals, the impeller, the new brass weight in the same order the old ones were, and screwed on the "X" on the end as snug as I could. Then I carefully reattached the motor and housing to the bottom of the dishwasher, ensuring good solid seals and tightening that big ring again from the inside as snug as I could get it, carefully hooked everything on the bottom back up basically in the reverse of disassembly, put the unit back under the counter, plugged it in, turned the water back on to it, loaded it and tested it. I was fortunate enough to not have it leak anywhere, after 3 or 4 loads I reattached the bottom trim pieces and checked this off my list. Also, would love to mention that your site is great, the parts were priced attractively, they arrived very quickly and were a snap to install.
