Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 653AJ-V-CX > Instructions

653AJ-V-CX Admiral Range - Instructions

All installation instructions for 653AJ-V-CX parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 653AJ-V-CX
1-15 of 116
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Drip bowls were burned and tacky

  • Customer: Donna from Dallas, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 461 of 462 people found this instruction helpful
First I removed the old bowls and replaced them with the new.

Drip bowls needed to be replaced

  • Customer: John from Chester, VT
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 447 of 529 people found this instruction helpful
took old bowls out, put new bowls in, took a coffee break

Stove top element not working due to bad receptacle.

  • Customer: Richard from Carthage, NC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 153 of 165 people found this instruction helpful
Turned off the power at the breaker box, cut the wires approximately 5 inches from the bad receptacle and removed it after removing one screw. Stripped back the wires about 1/2 inch and attached the new wires with the ceramic wire nuts provided and secured the receptacle back in place with the new screw provided in the kit.
My sister's husband wanted to scrap the whole range but I repaired it with $14.00 worth of parts.
The element is working great now.
Whenever I need appliance parts again I'll use partselect.com.

Old drip pans stained

  • Customer: Linda from Atlanta, GA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 210 of 412 people found this instruction helpful
Replaced old drip pans with new ones - very easy - even a 68 yr old lady can do it!!

one of my burners would only work half the time, and you had to wobble it to make it work

  • Customer: cindy from Sebeka, MN
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 131 of 252 people found this instruction helpful
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires, connected the new element using the wire caps, and finished bye rescrewing the element backinto place.

We needed new drip pans and no one carried the model we needed

  • Customer: sylvia from ventnor city, NJ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 65 of 66 people found this instruction helpful
we removed the old pans after first removing the electric heating element and simply inserted tne new pans

Burned terminal block and filter board

  • Customer: Joseph from Decatur, GA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set, Wrench set
  • 75 of 158 people found this instruction helpful
Removed and replaced above named parts, rewired.Be sure to tighten all nuts that secure wires. I believe this is what caused the problem.

Element burned out

  • Customer: Anita from Hudson, CO
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 17 of 27 people found this instruction helpful
Unplug Stove removed screws pulled out
element. Lifted off the wires with a pliers they slid
onto the element ends that were pointed up
was very easy.

spring broke on one side of door hinge

  • Customer: Travis from Lexington, OK
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 11 of 14 people found this instruction helpful
Pulled the stove out, removed the sides and attatched the new springs( replaced both while the stove was out). Worked like new and put the stove back.

Burner was out but the burner coil worked on onother burner

  • Customer: Richard from Orange, CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 7 of 7 people found this instruction helpful
Replaced receptacle but it was not the problem. After further inspection I believe that the problem is the switch. The switch is on order now from Part Select.

Store-bought drip bowls wouldn't fit.

  • Customer: Sharon from Yacolt, WA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 5 of 6 people found this instruction helpful
My elements just plug in so all I had to do was pull them out and replace the drip bowls. They fit perfectly!

electric coils would not stay flat as drip pans were incorrect fit

  • Customer: Janet from Philadelphia, PA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 5 of 6 people found this instruction helpful
replaced drip pans with correct type

The heating element socket had crumbled with age.

  • Customer: Edward from Webster, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 4 of 4 people found this instruction helpful
Changing the socket with a new one simply required removing one screw and splicing the two existing wires to the pigtails on the new socket. It took longer to unpack the replacement part than actually doing the job.

Door Spring Broke

  • Customer: Thomas from Van Nuys, CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 5 of 7 people found this instruction helpful
Removed 7 screws on sides and one on top of stove. Replaced both springs (only one was broken but did both). Took around 15 to 30 minutes from start to finish.Fastest shipping in history during holidays without paying anything extra.

burner receptacle burned out

  • Customer: Michael from N. Haverhill, NH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 4 of 5 people found this instruction helpful
Worst part of the job was removing the old screws that held the two old rectecles in place for the two burners I repaired. Once the screws were removed cut the wires stripped them and used the porceliean wire nuts provided with the kit. Easy job and good instructions.
All Instructions for the 653AJ-V-CX
1-15 of 116