All Installation Instructions for KitchenAid Mixer 5KSM150PSBAP4

Stripped plastic gearr

Opened beater , removed grease , took bearing off , removed alignment pins ,pulled shaft and pinion out , replaced parts , lubricated with new grease , assembled the whole drive . do not like the plastic gear or the clearance once assembled has a lot of slop for this type of drive .

Parts Used:

Washer

Worm Gear

Shaft & Pinion (10T)

BEARING

CONRADT from El Paso, TX
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

Was this instruction helpful to you?

Thank you for voting!

worm gear had broken tooth and gear was loose on sprocket

I dismantled the machine to find the problem and to see what part I needed. Than when I ordered the part I saw the video of how to do it. If I had seen the video before I dismantled, I would have save a few steps. The video was very complete and accurate even it being an older model

Parts Used:

Worm Gear and Bracket

Larry from Briggsdale, CO
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

Broken Part to KitchenAid Mixer

Great experience. Reasonable cost. Quick delivery. Would certainly use PartSelect again

Parts Used:

Thumb Screw - Black

PJ from Rome, GA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Thank you for voting!

My wife was complaining of a loud grinding noise.

I replaced the brushes. I didn't realize that I've put one of them wrong. Reminder for next time the brushes have to touch the rotor of the motor. It took me a little bit to understand but the brushes can go in and not touch the rotor. It works very quietly now. Thank you PartSelect for your infos and knowledge.

Parts Used:

Motor Brush

Nick from Naperville, IL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

Bad Transmission

Task went EZ,I have two with bad transmission and with fixing them I found out the grease in case housing was bad like wax. So I'm going to check out my third mixer and replace old grease in that one. your part scrimatics are great thanks.

Parts Used:

Worm Gear and Bracket

Transmission Case Gasket

Norman from Norwich, CT
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers

Was this instruction helpful to you?

Thank you for voting!

Stripped worm follower gear.

Watched the video. Ordered the parts. Watched the video again. Replaced the worm follower gear and bearings on the worm gear. Added grease. Installed new gear housing. Put it all back together and tested. Works like new. Now I get cakes and goodies again and have a happy wife who thinks I'm super handyman. Thanks

Parts Used:

Stand Mixer Gear Grease

Johnna from Childress, TX
Difficulty Level:
Really Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

Worm gear was bad

Order part through parts select. it only took 3 days to receive part. The mixer was very easy to take apart and to replace the gear. it was back together in about 20 min. The video from kitchen aid to repair the unit is awsome. Thanks

Parts Used:

Worm Gear and Bracket

Alvaro from Brighton, CO
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

After 25 faithful years , it deserved grease,contacts & brushes

Downloaded a KitchenAide rebuild manual. Took it totally apart, inspected all the parts for wear and breakage, Cleaned and reassembled with new parts and grease. I only bought one extra part, the screw-stat. I was pleased with the parts and fast service, thanksLarry

Parts Used:

BOARD-PHAS

Motor Brush

Speed Governor

Speed Control Plate

Laurence from Redlands, CA
Difficulty Level:
A Bit Difficult
Total Repair Time:
More than 2 hours
Tools:
Pliers, Screw drivers, Wrench set

Was this instruction helpful to you?

Thank you for voting!

This mixer was found, in apparent brand-new shape, discarded at our trash transfer. It had a stripped worm gear.

I disassembled the mixer head, removed old grease and cleaned interior completely. I noticed the worm gear was broken and concluded some lazy person hadn't bothered to find out why this otherwise pristine machine didn't work. I ordered the parts from you, installed a new worm gear, repacked with food grade grease, put on the new gasket, reassembled and turned it on. TA DA!!! Since I have a 50 year old KitchenAid in fantastic condition, I gave this one to my neighbor. She cooks for about 15 people on Sundays and has never had a stand mixer until today.

Parts Used:

Worm Gear