Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 59673503201 > Instructions

59673503201 Kenmore Refrigerator - Instructions

All installation instructions for 59673503201 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 59673503201
646-660 of 1,076
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Water Filter Replacement

  • Customer: Ralph from Georgrtown, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
It was very easy, just unscrew old filter and screw in the new filter. Reset the warning light, and done. Ralph Mason, 403 Sundance Lane, Georgetown, TX 78633

Replace Pantry End Cap - Right Side

  • Customer: Lyman from Searcy, AR
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
(Always pay attention to where parts are located and how you remove them.) 1) Remove vegetable and fruit drawers above the pantry. 2) Lift out the glass pantry top. 3) Remove the rails which support the glass pantry top and remove the pantry drawer. 4) Operate the temperature control lever on the end cap while observing the movement of the sliding vent covers just above the back of the pantry drawer. 5) Remove the 3 screws which secure the end cap. 6) Carefully pull the end cap away from the side of the cabinet, taking care not to break any of the attached pieces. 7) Remove the components that control the temperature of the pantry. Some must be rotated to bring the component through a slot (or similar arrangement) - the control arm snaps into a hole in the center back of the cabinet... so you may need to use a flat screwdriver to assist in freeing it. 7) Install the components just removed onto the new end cap. 8) Re-attach the control bar in the back of the cabinet. (Its other end is now attached to the new end cap.) 9) Position the end cap and secure it to the cabinet with the 3 screws. Before snugging them up, test them to insure that the temperature control is sliding correctly. 10) If all is well, snug up the screws. 11) Re-install the glass support rails, glass, pantry drawer and the veg and fruit drawers. 12) Place the left end of the front cover of the pantry drawer on the hinge pin on the left side. Carefully bow the cover to allow the right side to be slid over its hing pin on the right end cap. Job done. In the future, take care to insure that the pantry draw is pushed in and the cover is closed BEFORE you close either of the two doors on the refrigerator!

Right hinge broke when wife dropped a candy apple on the deli drawer lid.

  • Customer: James from Toano, VA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Couldn't have been easier. Remove the glass plate. The deli drawer lifts out of the slides. Two screws later, the entire assembly was out. Be careful with the adjustable vent that is attached to the right end cap. Gently pull out the end cap, the vent just has a tab on the very end that inserts into the rear wall of the fridge. After that, reverse for installation. JMC

Broken drawer

  • Customer: Elizabeth from Oak Bluffs, MA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I was opening the bottom pull-out as my girlfriend had open the veggie drawer above it, without realizing that the lid would swing up. In other words, on this French door fridge, you can only open one drawer at a time, all the while dumping all the cold air out at once. Im not sure why this model is popular! But its a two door top with bottom freezer, new and expensive, and on Martha's Vineyard-a shipping nightmare (planes, trucks, ferries, more trucks). I was visiting and needed to make amends for busting things up, and quick, before leaving to go home. My boyfriend found PartSelect online, I made an order at 247pm on Thursday (cut off for "next-day" is 3p, so you didn't guarantee it would come before Monday), but the warehouse shipped it anyway by 630p Friday evening, on island! The parts were cheap at about $25 each, the instructions were do-able, the blow out diagram online made it easy to know what I needed, and the whole thing was good-as-new in 48 hours. What a godsend! Thanks PartSelect, for saving me! For $75! Woohoo- (I'll take care of the boyfriend...)

Ice Maker worked sporadically and then started dropping water into bin, make a large chunk.

  • Customer: Harold from Spring Branch, TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Was very happy with the experience of using your company. The man on the phone was helpful. The icemaker shipping was only about $7 and got here in a couple of days. I liked the video, and then including a link to the video with the on-line confirmation. Was not quite sure it was the icemaker or the metering valve on the back, as the latter would make a little grinding noise, but the symptoms matched the dumping of water into the bin. After replacing, everything is working well. The only difficulty was the wire harness plugs into the other side of the back of the box than in the video and I found it a little difficult to route the wires correctly as they seemed too short. But a little trial and error solved that. My model is freezer on the bottom and I didn't notice that the little detachable funnel wasn't quite seated and it was necessary to reinstall, making sure the funnel stayed in place correctly. That was my own error. My overall experience was excellent and I would not hesitate to recommend PartSelect to anyone with an icemaker problem. I'm only sorry I lived with a recalcitrant ice maker for a couple of years before finally acting on it. I am glad I found your website! Lee in Texas

Freezer seal was broken

  • Customer: Sherry from Columbiaville, MI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Thanks to some reviews we found online about replacing gaskets, ours went very smoothly. One person said to soak the gasket in hot water, which we did til it was very soft. Installed like a breeze. Then, the same person said to tape the door closed after installation, we did that too. The gasket looks like it was professionally installed and we have never done it before. Thanks!

plastic pin on left side end cap broke off

  • Customer: robert from Columbus, OH
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
replaced the whole left side end cap. Biggest problem was taking out the trays. cleaning had to be done. Wow!refrigerators get dirty over time. The actual mechanical part was trival.

Not making ice, leaking water.

  • Customer: Robert from Youngstown, OH
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Removed icemaking mechanism replaced with new. Works better than ever

Water filter change

  • Customer: Michael from Dallas, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Easy unscrew remove and install new filter

Ice Maker would not make ice

  • Customer: Philip from Hoschton, GA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Quick repair especially with YouTube video; took less that 15 mins including moving ribbon cable & fill wire. Saved at least $200.

Ice cresents froze together in one big lump

  • Customer: Lloyd from Stilwell, KS
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Simple replacement of the icemaker solved the problem. I suspect the icemaker was overfilling resulting in water flowing into the ice reservoir.

Ice Maker not making ice

  • Customer: Ellen from Vienna, VA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Wrench set
  • 0 of 0 people found this instruction helpful
This was about 10 time easier than I had expected (I'm in my 30s, a mom). I put this off for almost a year groaning that I would have to spend tons of money on a repair man. It was really no big deal and took under 30 minutes. I used the video from PartsSelect, and it was right on. I was initially worried because the description from the website said that the new ice maker didn't come with the 'harness" and I had no idea what that was. Its just the little set of wires that easy unclips from the old unit and pops right into the new unit. Mine was reusable, so pretty easy. The only minor issue I had was that the new bracket didn't line up comepletely with the hole in the fridge where the screw went in, but I solved that with adding a skinny washer. Would definetly recommend any common-sensed person to do this repair yourself.

Ice maker was leaking

  • Customer: William from Noblesville, IN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I couldn't believe how easy it was since I am not the handiest guy. All it look was to switch over the wires and screw it to the inside of the freezer. I was back in business.

Icemaker had been sluggish for a while. We had to keep the wire (bale) in the off position for half hour or so, then put it back in the down position. After a few months of doing this, it stopped making ice altogether.

  • Customer: Elisabeth N from Katy, TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Shut off water and unplug fridge. Remove ice drawer. Unscrew one short nut underneath icemaker, and the two longer ones holding it to the wall of the freezer. Now remove white cover. It just needed a little jiggling w a flat head screwdriver to loosen it. Now you can see where the wire harness is connected, use the same flathead to depress the plastic pin holding it in place, and slide it out. Remove the wire harness from the metal clip on side of icemaker. Now you should be holding the old icemaker in your hands. Remove the bale carefully. Now install the bale into the new icemaker, while making sure it's in the 'down' or 'on' position. Bring the new icemaker into position, gently snap the wire harness into place, sliding the wire into the clip like it originally was. Fasten the three screws again. Then, finally, snap the white cover back into place. Slide the ice drawer back into position, turn on the water, plug the fridge back in and wait 30-45 minutes for your first batch of new ice cubes.

The ice in the ice maker would freeze into a solid block. Upon inspection I realized the ice maker was leaking water into the ice holder which was then freezing solid. Three tray for the ice maker was slightly rusted and caused the water to drip.

  • Customer: sal from lighthouse point, FL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I watched the video on how to change the ice maker, very easily explained, and removed the old in about 10 minutes.After seeing how the old one came out it only took five minutes to install the new one. The appliance repaircompany wanted$120 just to diagnose the problem,i bought the part from partselect for$104 total. This is the forth time I've used this site and saved a ton of money.
All Instructions for the 59673503201
646-660 of 1,076