Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 59673503201 > Instructions

59673503201 Kenmore Refrigerator - Instructions

All installation instructions for 59673503201 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 59673503201
586-600 of 1,076
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Replaced icemaker

  • Customer: Howard from Houston, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
1. Prepare the new ice maker by installing the bail cut off from old unit and installing the wiring harness from old ice maker. 2. Turn off the freezer unit only and turn off water supply. 3. Unplugged the electrical connector from the ice maker to the plug in back of freezer compartment. Remove the three (3) screws holding ice maker in place. Placed the cap from old unit to new ice maker. 4. Plug the electrical connector to the plug in back of freezer. Attached new unit with the three screws. Place bail in on position and turn the freezer and water on, ice made in circa 3 hours (without leaking I might add :)

no ice

  • Customer: Robert from Mondovi, WI
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Easy

Light on refrigerator went on to replace filter

  • Customer: CAROL M from TUCSON, AZ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Just replaced a water/ice filter..

Broken Water Nozzle at Door

  • Customer: Chris from Brentwood, TN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
(1) Ordered PS371704 from PartSelect! Best advice EVER! (2) Unplugged refrigerator (since the water solenoid on the back of the refrigerator is powered to switch ON the water, you NEVER have to turn off the water!) (3) Pull off the refrigerator's bottom grill. (4) With a small saucer under the fittings, unscrew the black and white tube fitting. There is only one nut to remove on the white tubing side. You'll need to undo the compression fitting on the black tubing and slide off the compression nut. You'll need to MAKE SURE you keep these nuts and replace onto the black and white tubing the SAME WAY you took them off. You'll NOT need to use nut drivers as finger tight is the key. Too hard and you'll ruin these plastic nuts. You should get only about 1/8 cup or less of water during this whole exercise. (5) Cut off the old, broken water nozzle. (4) Find a screw of the appropriate size to fit tightly 1/2 way inside the new tubing (this is to ensure your old and new tubing are connected to feed through the door). If screw is not tight within the tubing, wrap part of a plastic (thin) sack around this screw a couple of times and force into the tubing. You'll, of course, then need to use the hacksaw to cut the head off the screw as you'll be forcing the other half of the screw into the old cut tubing (6) Chase the dog out of the kitchen and cajole your wife (significant other) to push the newly joined tubes through the top of the dispenser, through the door and out the bottom as you will be gently PULLING on this old tubing from the bottom until the new tubing pops through the doors bottom. (7) Once this new tubing is out, you will separate the old tubing and, using the nuts in the proper sequence, connect this new tubing to the white tubing. (8) Plug the refrigerator back in and test flow the water. Check to ensure the plastic nuts have no leakage ... button up the bottom grill ... and enjoy the fresh water! PS> Don't forget to praise the wife (significant other) and give the dog a treat for staying out of your face!!

Drawer slide had a busted hinge pin

  • Customer: Stephen from Cottonwood, AZ
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
removed the two drawers. due to the refigerator location, had to remove the door. Then it was just 3 screws and put in the new end cap and then replace drawers and door. Job is done in less than 20 min and the wife is happy again.

Installed new Ice Maker

  • Customer: James from Chatsworth, CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Followed the instructions from the excellent video by Steve on your website which made the installation easy.

Loud, non-rythmic clicking noise shortly after the compressor comes on, continuing for several seconds.

  • Customer: PHILLIP from SUN CITY CENTER, FL
  • Difficulty: Easy
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Replaced the "Run Capacitor. The non-rythmic clicking associated with the compressor coming on continues. The problem was obviously not the Run Capacitor". I don't know what to do next. Any suggestion would be appreciated.

Thanks,

Phillip

Plastic clips that held in clear plexiglass broke off

  • Customer: Kenneth from Howell, NJ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Very easy to replace the old broken piece with the new one. Simple

left pin for deli cover brken

  • Customer: Paul from Tucson, AZ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
removed deli tray and produce drawers.removed three screws with nut driver;removed track;trannfered track;reinstalled lefgt end cap.

Filter needed changing

  • Customer: Lynn from Rome, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Simple! Pop the case open. Counterclockwise to remove old filter. Wipe out excess water. Unwrap new filter; remove tab. Place in filter holder; turn clockwise. Close case. Run water to remove air. Couldn't have been easier!

My original ice maker was leaking

  • Customer: Joyce from West Palm Beach, FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I went online to PartSelect to see how much I'd expect to pay for the ice maker assembly if I called an appliance repairman to fix it. Instead I found an awesome, very well described video on how to do it myself. I ordered the part and paid ground shipping, but received it the next day!! Installation was a breeze (except I got help removing the electrical jacket because it was an awkward angle and I was afraid that I would damage it). The experience did as much for my single, 55 yr. old self esteem as it did for my wallet. Thank you PartSelect! I'll be back!

Not making ice

  • Customer: Larry from Sun City, AZ
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Repair was very easy. I watched the video and read the descriptions by other customers and it was just as described. Had ice again in about 4 hours and has been working great since.

No ice.

  • Customer: Dennis from Lexington, OH
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
(1) Watched the PartSelect installation video. (2) Placed Order. Arrived in two days, regular delivery. (3) Opened package. (4) Selected installation tool. (5)Removed old Ice Maker Assemply (6) Replaced w/new. Ice in a couple of hours. Video & order/delivery aside, the entire process took less than 10 minutes including selecting tool and opening package. PartSelect video very helpful.

Ordered ejector arm.

  • Customer: Joyce from Springfield, MO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
No instructions with part. Found a picture on line and changed the arm, but it didn't fix the problem. Fairly easy after figured out what needed to be done to get to the part.

water running in ice cube tray

  • Customer: Thomas from Sussex, WI
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
After watching the video witch was GREAT help THANK YOU
All Instructions for the 59673503201
586-600 of 1,076