Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 59673503201 > Instructions

59673503201 Kenmore Refrigerator - Instructions

All installation instructions for 59673503201 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 59673503201
571-585 of 1,076
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Leaked water as filling

  • Customer: Walter from Torrance, CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 43 of 1234 people found this instruction helpful
Removed mounting screws
Disconnected file hose
Flipped unit over to remove connecter
(This was the only difficult operation; unpluging & pluging it in)
New part fit was very good
Reversed the disassembly order to install
New assembly had to cycle a while to produce ice cubes. I'm very happy now, so bring on the hot weather.

I was overdue for a new water filter

  • Customer: amelia from Henniker, NH
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
removed the old filter. unwrapped the new one. peeled off the protective foil. inserted new filter as directed. placed old filter in sink to drain. ran "water" from dispenser to purge air from line. Shazam!

Broken pantry end cap

  • Customer: Carter from Athens, GA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
The repair was straight-forward once the pantry drawer and lower shelves were emptied and removed - remove the mounting screws, replace the broken end cap with the new part. It took me several minutes to reattach everything. It took me longer to clean up all the old food spills under the pantry drawer.

Repace Water filter

  • Customer: Nancy from Urbandale, IA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
20 seconds. Easy Easy.

Ice maker stopped working. Turned out a connection on the heating bar shorted out.

  • Customer: Russ from Supply, NC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Pulled the plug on the refrig. ( This is important since the heating bar on the bottom of the ice maker could come on as soon as you plug it in and burn your hand ). Removed the ice bin to get it out of the way and then removed the 1/4" hex screw from the support bracket under the old ice maker ( don't lose it ). Pushed up on the old ice maker to dislodge it from the 2 support clips on the top of the ice maker. Squeezed both sides of the wire harness plug and pulled it out and removed the old ice maker. Removed the wire harness and level bar from the old ice maker and installed them on the new ice maker. Plugged the ice maker wire harness into the female receptacle in the freezer. Popped the ice maker in to the top support clips making sure the rubber water chute from the refrig. was in place in the round ice maker receptacle. Plugged bak in the refrig. and I was getting ice in about 2 hours. Working fine after 1 week producing plenty of ice. RussK---

ice maker stopped making ice

  • Customer: David from Jacksonville, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
following the advice of this site, purchased a new ice maker. Old one was simple to unhook and remove and new one was just as easy to install. Within no time at all, I had ice being made and it has been working perfect since. Thank you for the help...

Broken prong that held the lid for the drawer

  • Customer: Patricia from Fernandina Beach, FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Removed the old bar. Replaced the part that moved the shutter open and closed. Installed the new parts. Put the drawer lid back in place. Working fine. Thanks!!

A bit difficult to reach inside the refrigerator

  • Customer: Edward A from St Joseph, MO
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
I used the feedback information from others who commented on your website

Ice Maker was not functioning

  • Customer: BRET from SAN DIEGO, CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I followed your posted video. Did step by step as video instructed and in about 30 minutes finished. Ice was made approx 30 minutes later. I hope you do more videos, a picture is worth a thousand words.

I needed a larger ice pan for the freezer.

  • Customer: Dorothy from Westford, MA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I took out the old one and put in the new one. For some reason the repair story associated with the ice bucket had nothing to do with ice buckets.

changing the water/ice filter

  • Customer: Ellen from Fairfield, CT
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Opened up the compartment where the old filter was located, twisted it to take it out (be careful not to spill water in the filter!), and installed the new one. Even a 64 year old woman had no trouble!

Frost in bottom freezer, freezer 8%, ice maker works

  • Customer: Richard from Smyrna, GA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
replaced electric control board, defrost for six hours. next day (24 hours) same problem, dusterhoff2928@charter.net

Leaking water

  • Customer: Terry L. from Glasgow, KY
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed Ice bin, remove rails on left side that hold ice bin. Remove one screw holding ice maker to refrigerator wall,then lift ice maker off holding screws. Unplug wire harness from back of refrigerator. Remove wire harness and loading wire from old ice maker and install on new unit. Re-install new ice maker by reversing steps. Videos where very helpful.

Like many others, the tab broke off that held the drawer in place.

  • Customer: Jerry from Odessa, TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I took out the two shelves that were in the way. Lifted the glass out and set it aside. Since the pantry drawer cover wasn't in, because the tab was broke, I lifted the support beam out, pulled out the drawer and lifted it out. (The pantry drawer just lifts right out, straight up then towards you) I took out the back support beam, it lifts straight up. After that, I used a screw driver to take the pantry drawer glider (part #12) off of the broken one, then I put it on the new one so I wouldn't forget its orientation to the new part. I used a my socket set to take out two (should be three, but mine had two) bolts. I then gently pulled off the part needing replaced, first pulling it to the left, bringing the SLIDE- TEM (part #11) the BAR- TEMP (part #15) with it. Part #11 is held in by a tab at the back, to the left, so when you have the whole thing at the correct angle, it just slides out. (Pulling to the right, when you have the whole piece angled towards the center of the fridge, to the left.) After you get that piece out, you'll be able to clean the bottom of the fridge, it's amazing how much crap builds up on the bottom! (I even found a dead fly, eww! LOL) Taking parts #11 & #15 off of your old piece is easy, two tabs that you bend in on the right side of part #11 loosens it from your old part, then twisting it to take the pieces apart then lifting a few tabs to get #15 off of the old part. Then twisting it again to get the KNOB-TEMP (part #14) off. Pay attention to how you take this apart! It goes back together just like it came off! Attach these pieces to your new piece then it slides right in like you took it out. Slide the back left of #11 into the tab, reinsert the bolts, put your support bars back in, put your drawer in, put the drawer cover back into the new tab you just installed, put your glass in and finally, your shelves. All done!

The icemaker was leaking into the ice hopper creating an iceberg.

  • Customer: Peter from Hemet, CA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
After receiving the new ice maker assembly I placed the new part next to the old one to see what I needed to transfer from the old to the new. After removing the wiring harness and a few small parts, I placed them on the new assembly. After that it was a snap which timewise took about 15 minutes. I am pleased to say the ice hopper is full and being replenished very efficiently.
All Instructions for the 59673503201
571-585 of 1,076