Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 57731H9WW > Instructions

57731H9WW General Electric Washer - Instructions

All installation instructions for 57731H9WW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 57731H9WW
361-375 of 512
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

had a pin hole in the drain pipe

  • Customer: ROBERT from Bynum, TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
order the part and replaced it and it works just great! May I add never before have I had such an amazing experience in dealing with your company, your company shows pictures and I ordered the part in the late afternoon and I had it the next day, the diagram you show on your site was so helpful, you told us that the part now is replaced with a different #. Once again KUDOS!! to your co.

knob stripped

  • Customer: sandra from north windham, CT
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
needle nose pliers to pull out old tab behind old knob. simply pop new knob on when you remove old. video gave me self confidence to do it myself.

it was leaking

  • Customer: Beverly from Casper, WY
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
my son repaired it. I was told that I had to by the whole thing as you could not get parts. Thank you for the parts.

No hot water fill

  • Customer: Joanne from Millican, TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Installation went okay but still only get cold water fill

The timer knob was stripped.

  • Customer: Steven from North Arlington, AL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I watched the video and did the same thing that was shown. It was a very easy process!

Start Button Fell Off

  • Customer: PHYLLIS from north lauderdale, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Turned off all power. . . Took top back off. . . Retored starter back in position. . . Attached knob. . . Replaced back, turned on power. . . And thanks to utbe instructions

The timer knob was broke

  • Customer: Thurman from Marshall, IL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Watched the video you had on how to replace it and did it like you showed and said and it worked fine.

water pump died

  • Customer: Richard from Mansfield, OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
Was easy. Removed pump, ordered yours and replaced

knob stripped

  • Customer: Robert from Strasburg, VA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
Pulled clip off and installed new knob

Leaking water on final pump out

  • Customer: Francis from Rochester, NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Removed front panal & operate to see leak origion. Found the side of the pump cracked and split. Part Select sent the exact replacement part! Unplug washer. Remove ront panal; using a putty knife and a bit of preasure at the two release clips. Using pliers or small vise grips, squeeze hose clamps and locate back out of the way and remove two hoses. Have a shallow pan below to catch remainig water. Unhook the electric connections, taking note of where. Using nut driver or small ratchet, remove the two mounting screws and pump. I used new screw type hose clamps in lieu of the originals.

Washer would not drain or Spin!

  • Customer: Danny from Clarksdale, MO
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Socket set
  • 0 of 0 people found this instruction helpful
First I unplugged the washer and then removed the front panel of the washing machine using the puddy knife running it along the top edge approximately 3 inches inward from each corner found the tab on each end and pushed in with the knife until the panel popped loose from the top tabs. I then located the pump motor on the lower front right side of the machine and compared it to the new one that I had purchased,(they were the same) Note;be sure all the water is drained from the washer otherwise get ready for a bath approximately 1 gallon of water came out of the drain hose that is located on the back of the pump after using the pliers to squeeze the clap and remove the hose,this was the worst of the whole job,then remove the inlet hose on the top by squeezing the spring clamp with the pliers. Next unplug the harness located in the front of the pump,and then last take a 1/4 drive ratchet w/extension and a 10 mm socket and remove the 2 hex screws on the mounting plate. Install the new pump and motor assembly in reverse order with the instructions above and you should be washing clothes in no time. Thanks

The old knob would not let me select the wash setting.

  • Customer: Thomas M. from Hamilton,, NJ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
I took the pliers pulled the plastic clip off the back of the knob and pulled the knob off the dial lifted the dial off. I pushed the new dial on then pushed the new knob on and I was done. The hardest thing was to open the plastic bags the parts came in. The next time I will use a knife or something else to open the bags

leaking drain line

  • Customer: frederick from CHARLOTTE, NC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
took screw driver unscrew the srews remove the drain hole stuck the new hole in it,s place and replace with new srews that was it.

Timer Knob was turning the dial for settings.

  • Customer: Keith from Woodhaven, MI
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
I pulled the clip that locks the knob on the dial. This releases the knob. That is where I saw the wear on the plastic teeth that turns the dial. I replaced the knob with new part from PartSelect.com and replaced the clip. Partselect.com had my parts delivered to my residence within 3 days.

Agitator did not move

  • Customer: David from Albion, MI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
With the instructions found online, this was a quick easy repair. I used youtube to have video to show the method. Used rope to pull up agitator, used wrench to loosen bolt and then put back together. Part was delivered really fast, I recommend Partselect.com for the parts you need!
All Instructions for the 57731H9WW
361-375 of 512