4KSRS25QFW00 KitchenAid Refrigerator - Instructions

The hardest part was to figure out how to remove the old studs and put in new ones. I figured out finally that they should be twisted out and in., Simple online or printed insruction would be very helpful. Unfortunatelly the manual does not contain any repair information.
I fixed it with little trouble.

First I removed the old lightbulb from the socket and replaced it with a new one to confirm that the bulb was not the problem. I then pryed the socket out with a flat-head screwdriver. I could tell that the socket was anchored in its hole with clips so it was relatively easy to pry it out. Once the socket was out, I disconnected the lead wires and ordered a replacement socket kit from Partselect. When the new one arrived, I reconnected the lead wires to it, snapped it back into its hole, screwed in a new lightbulb, and presto!! The light was back on with no further problem. Thank you, Partselect!! A $15.00 part saved me what probably would have been at least a $100. service call and heaven knows what the technician would have told me I needed!!!

Took all the screws out of the plastic shroud that encloses the switch .There only four that I needed to remove, were the two in front where the switches that go,they go in horizontally and two in the back with large washers on them that hold the back to the top of the box that go in vertically.The switch was a snap ( make that two snaps ) the wiring is almost self explanatory. then it gos back to the way you took it off. OH! and don't forget to turn the light bulb all the way back in to the socket , so the light will work after you take the time to install it yourself.I had the water supply line from under the box to the water dispenser in the door and the total bill on that was one hundred thirty seven and a hand full of change.Don't be afraid to do it yourself the savings is enough on one one item to make several months payments on a new one Randy the "Handy Man'

The repair was actually easy; however I have an ice dispencer/crusher attached and the which the diagram supplied with the part did not include. I had to make several calls before I was e-mailed the diagram.
Suggestions: note that the screw at the end of the auger goes in the reverse direction (this took me about 20 minutes to figure out even though it was shown in the diagram). Also, be sure to keep the ice crusher parts in order and be sure the white plastic tab on the crusher fits into a depression in the housing. I did not notice this and had to take it all apart and redo the install. It works great!!!

Please note the part I ordered is actually the meat pan shelf/frame. It is listed incorrectly on your site as the crisper drawer cover/frame. The pictures are correct though.

It is really easy to replace. I just removed the crisper drawer which is above it to get room to work. Then I removed the glass insert from the meat pan cover. I then removed the frame by lifting up on the front edge and then pulling it forward and away from the back two support pins.

Don't forget to tranfer the gaskets and air deflector from the old shelf to the new shelf.

Insert the new frame by sliding it back onto the two rear support pins and then lowering the front edge down to rest on the two front support pins. Replace the glass and drawer.

The control bracket is made of plastic and holds two microswitches that activate the ice dispenser and the water dispenser. The plastic clips that held the switches on the control bracket broke so that the switches no longer operated when the ice dispenser lever was operated.

Two screws held the external dispenser bezel, and two screws held the control bracket in place. The wiring and switches were transferred to the new bracket and the new bracket screwed into place. Then the bezel was replaced.

Total repair time was less than 5 minutes. The control bracket was $16.50 with shipping and arrived two days after I placed the order.

The PartSelect website had a clear diagram of the control bracket so I was comfortable with the order.

After removing all the food items from the door, I popped the plastic cover off of the hinge assembly located on the top of the door. With a fine point Sharpie pen , I marked the outline of around the hinge assembly so I could return it to original position. I then loosened each of the 3 bolts holding the hinge on just enough to allow me to clear the pin of the hinge out of the hole in the door. Once the top was free of the hinge, I lifted the door off of the bottom hinge/pin assembly. My cam parts on the bottom hinge and door were either broken and/or partially missing. I removed the broken and worn pieces by removing each of the screws holding the top and bottom (of the bottom hinge assembly) cam pieces and installed the new ones using same screws. I then reversed the steps and slid the bottom of the door back onto the bottom hinge assembly and then lifted the top hinge enough to allow the hinge pin to slid back into the hole on top of the door. Positioned the hinge so it matched the outline and tightened the 3 bolts. I checked the closing and made a slight adjustment to door as one of the shelves was hitting the interior as it tried to close. I did this by loosening the 3 bolts and pushing the door up and to the right (this door was on the right side of refrigerator). Tightened the bolts and reinstalled the hinge cover.
Pretty easy. My door cams were a little different so I didn't use all the parts in the kit. My shims were metal and did not move when I replace the cams so I didn't use anything in this repair except the 2 lower cam parts. I also put some grease/vaseline on the cams to lubricate them.
I figure the plastic cams just wore out over the years and all the heavy junk we put in the door shelves. I lived with this problem about 2 years before it donned on me that it was probably just a plastic piece or two that was broken or worn out.

1) At bottom of ice maker trim there are two small slots at right and left ; use screw driver to pry away from door; lift trim upward away from door 2)using 1/4" nutdriver remove screws from 4 corners, 3) remove 2 screws from control panel 4) disconnect all wires/cables and set exterior panel aside. 5) locate 2" pin that runs through door spring and use needle nose pliers to remove round clip on left end of pin don't lose this clip 6) while pushing ice maker lever (where you would push with your glass) use needle nose to pull the long pin out to the right 7) Remove all remaining parts by hand (i.e. the pin, the dash pot and white lever and the ice door) 8)slide new control lever into slots on exterior side of the new door 9) -tricky part- using needle nose, push pin back through the right hinge point, the new lever, the new door, the new spring and the left hinge point (note the new door has no electric wire connector) 10) using the needle nose, carefully replace the little round clip on the left end of the metal pin. 11) reconnect all the wires (don't worry about the wire that had been connected to the door wire, just fold it aside) 12) replace two screws screws in control panel and four screws at corners of exterior panel 13) snap outer trim panel back in place.

Originally replaced water inlet valve, not the problem. Tried to work from cheap to expensive.
1. Turn off power, shut off water supply
2. Loosen top two screws of ice maker (will slide up and off, no need to take top two out)
3.Remove bottom screw from ice maker
4.Pulled unit, snapped out existing wire harness
5.Cut hole for water inlet on end of new unit and attached wire icemaking on/off bracket.
6 Connected existing wiring harness to new unit
7. Slid new unit down onto top two screws, put in bottom screw and tightened all three
8. Turned on power and water supply
Had ice being made within two hours. Part Select has given me great service, highly recommend.

I removed two screws on the top and one underneath the unit. Then I disconnected the cable. The hardest part was getting the nut driver on the bottom screw because it was obscured by the unit. The replacement unit plugged right in! I got my first batch of ice in about 20 minutes. All I really needed was the timer unit, but the entire ice maker wasn't much more expensive, especially when you consider the time saved on installation!

open ice maker door, use mirror to view slot in front of ice maker, slip piece in place and done

The ice maker was not getting water. I hotwired the water valve by switching the connectors for the water dispenser and ice maker water valves and water flowed into the icemaker when the water dispenser lever was pushed. I wronly assumed the water valve was good. I removed the icemaker and determined that the gear motor was not getting power in the position the icemaker had stopped.In this position, the thermostat determines when the motor gets power so I replaced the thermostat. The icemaker still would not get water! As it turns out, the water solenoid was sticking due to a deteriorated rubber washer which let the solenoid plunger get too far out of the magnetic field. I replaced the water solenoid assy and all is well. Don't get fooled by hotwiring the valve. If it isn't getting water, the solenoid probably is the culprit.

Received my kit quickly. Job was fast and easy. Removed 3 screws with nutdriver and unpluged the wiring harness. Use a flat blade screwdriver to lift the tab on the plastic end cap of the harness. The icemaker comes out in one piece. The wiring harness that came installed on the replacement icemaker matched mine perfectly. (It comes with two others). I plugged the new one in, replaced the screws, bottom one first to help hold it while replacing the top two screws. I used the shut-off arm from my faulty icemaker. Turned the power back on and put 1/2 cup of water in the tray and walked away. Ice dropping into the bin was music to my ears. Didn't need any of the clips or things that came with the icemaker. It was basically a "plug and play". I'm so happy to have ice again, and at a great savings!

I had a technician called out to the house to look at repairing several appliances that all have broken parts after just 3 yrs of use. Hood, Microwave, Oven, Fridge all in need of minor repairs..

Anyway - the estimate was $240 to replace the ice maker. I ordered PS358591 for $104. and it came in a couple days.. I took out one screw - slid out the icemaker, unplugged it - plugged in new one and slid it in the slot - and done !! Took about 20 mins.. didnt need any of the wiring harnesses in the box from partselect. Was way to easy to do !!

Thank you !

First, I unplugged the power to the entire fridge, and then removed the ice tray and ice door. Next, I unplugged the flat plug in the very back left behind the icemaker. Then I removed the 1/4" hex head sheet metal screws (2) and the phillips head screw (1) that hold the icemaker to the left side of the freezer wall. New icemaker came with a different style trip arm, so I used it. Plugged new icemaker in before reattaching it with the same (3) screws. Replaced ice tray and door, plugged in fridge, and waited....Dumped its first batch of ice maybe a couple of hours later. Not much trouble-shooting is needed when the entire icemaker is as easy and relatively inexpensive to replace as this. Twenty minutes, max.