Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 4KMTW5755TW0 Maytag > Instructions

4KMTW5755TW0 Maytag Washer - Instructions

All installation instructions for 4KMTW5755TW0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 4KMTW5755TW0
76-90 of 303
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

washer would fill but not agitate. lifting and closing lid would eventually get it started. lid switch bad

  • Customer: Nels from SOUTH HAVEN, MI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 2 of 2 people found this instruction helpful
unplug washer. -remove two phillips head screws and two nut head screws holding control panel. -lift up control panel. -remove nut head screw on ground wire of switch. -release and remove switch. - put in new switch. - connect ground wire. -replace control panel and screws. -plug in washer. (depending on location of your washer move it to gain access to screws on back of control panel.- once done move washer back.)

clothes remain soaking wet after wash cycle

  • Customer: MICHAEL from lake elsinore, CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench set
  • 2 of 3 people found this instruction helpful
The video was well made and made repair easy. I like the fact the video also showed how everything went back. The most difficult part and most time consuming for me was putting the washer cabinet or housing back on. I had a hard time lining the sides onto the slot to lock in place....the minor cut on finger sustained during the process was worth it. It saved me from buying a new washer and the whole family are happy that they don't have to wring out the clothes before putting it the dryer. Thank you!

The splashguard on the lid kept falling off and eventually split.

  • Customer: Debra from Mentor, OH
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 3 people found this instruction helpful
Old one fell off in my hands. I just snapped the new one in its place. Super easy. Repairman wanted $43 for the part plus the labor of $39. THe part cost me just $20 with shipping. Thanks!

rubber seal broke aprt

  • Customer: Lisa from North Attleboro, MA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 3 people found this instruction helpful
slid the old seal off the lid and the new one popped on so easily
I do so many self- repairs at home now this was not even an issue.

Washer would not spin

  • Customer: Brant from Saxtons River, VT
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 2 of 3 people found this instruction helpful
Based on all the other info here, I thought "ah-ha! I need to replace the clutch assembly". So I ordered the part, it came the next day (to Vermont, even!) and started to disassemble the agitator, motor, etc. just as shown in the video. I don't think I would have attempted it if it had not been for the video. It made the process seem very straightforward and easy, as long as you are comfortable using a socket set.

That said, there were some fairly minor differences between my machine and the one in the video, so your repair might differ a little. First of all, I did not need one of those spanners / tub wrenches (whatever they called it in the video-- the thing he hit with the sledge hammer) to take off that nut under the agitator. I didn't need to remove it, and the drive axle just pulled right out. Second, you really don't need to remove the motor mount. Just take the motor off, and then go right to removing the three bolts on the transmission.

Actually, my problem turned out to be NOT the clutch assembly, but the little plastic gear things that go between the motor and the transmission, fitting into that rubber ring thing. I lifted the motor off and one of them was sitting there in pieces! You can easily order this part, and it's even easier to install than the clutch assembly. The plastic pieces are reinforced with metal now, which seems like a good idea.

All in all, this was a fun little project, and now I am under the (probably false) impression that I can repair any problem with washing machines!

The machine would cycle properly all the time.

  • Customer: Kenneth from Carmel, IN
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 3 of 7 people found this instruction helpful
I read the experiences of others on this site and determined that the problem was probably the lid switch. Used others experience in taking the panel off and removed the old switch and inserted the new one. The post to be sure to have the lid open was good and probably saved me some time. Overall, the fix was simple and the problem appears to have been solved. The lid switch got here the day after I ordered it and that was great service. Better than paying for a service call or new washer.

washer wouldn't come on, power turned on but no action

  • Customer: james from Cumming, GA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 3 of 7 people found this instruction helpful
removed the top cover (with all the knobs on it) by releasing the holds in the back
removed the screw holding the lid in place
pinched the snap and removed the part

pinched the snap on the new one and seated in in the hole
screwed in the screw (lol)
turned on the washer

the rubber lid seal had torn and was falling off of the lid.

  • Customer: VICKIE from MEQUON, WI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 4 people found this instruction helpful
I removed the torn part which just pulled off of the lid and snapped in the new piece. No tools were needed. I also wanted to add that it was great doing business with Part Select. The part came well packaged, it came in a timely manner, and it was the correct part ! I will try Part Select for any of my future repair part needs.
Thank you

Agitator seperated from inside of wash drum

  • Customer: Larry from Brandon, FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 1 of 1 people found this instruction helpful
I had to find a point of reference first since item came apart in wash cycle and internal pieces fell out - thank goodness for YOUTUBE. Another guy was thoughtful enough to do a video on how the assembly came apart / went back together - a huge help for sure. Actual repair was less than a half hour after obtaining new part and seeing video. The 12 year old washer works like brand new - saving me close to 1,000 dollar replacement charges.

Bad lid sensor

  • Customer: Michael from ATLANTA, GA
  • Difficulty: Very Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
Ordered and replaced the sensor. Fairly simple. Washer runs good now. Thank you!

Washer would not start consistently when lid was closed. Water filled, but cycle would not start

  • Customer: Jessica from Jewett, NY
  • Difficulty: Very Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 1 of 1 people found this instruction helpful
Unplug the washer. Used flat blade screwdriver under each end of the control housing on top of the machine. This popped the spring clips and allowed the control housing to be lifted up and rotated out of the way. Once out of the way, lift clip on wiring harness to lid switch, then pull the harness off. Use nutdriver to remove screw holding ground wire in place. Open lid of the machine. Pinch tab on back of the lid switch and rotate the switch up and out of the machine. Insert the new switch in the same manner, making sure that the machine lid remains open until the switch snaps into place. Attach ground wire using screw removed earlier and nutdriver. Clip wiring harness back in place. Close the lid and then rotate the control housing downward, and press on both ends to re-engage the spring clips which hold it down.

drum would not spin during drain cycle

  • Customer: Art from San Mateo, CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 1 of 1 people found this instruction helpful
Your installation videos are the best thing ever!!! Anyone who is mechanically savvy can repair anything following your instructions. Thank you SO much. I watched the video a couple of times, took some notes, and replaced the clutch. Problem solved. So, thank you for carrying a multitude of parts, quick shipping, and for the videos. I can repair almost anything, but your services make it time and cost effective in an era where the mantra is discard and replace.

Shakes during spin cycle

  • Customer: Ronald from CLEVELAND, OH
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
Removed housing, using pry bar lifted plate used screwdriver removed wear pads one at a time. inserted new ones and snapped into place. Did not have to remove tub. Be sure pry bar does not slip and you pinch your fingers. Machine works just fine know.

Bad clutch

  • Customer: james from MIDDLETOWN, NY
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 1 of 1 people found this instruction helpful
Watched your video and it was right on so helpful it made my job easy.

Loud bang at the end of the spin cycle and symptoms of an unbalanced load.

  • Customer: mark from murfreesboro, TN
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 2 of 4 people found this instruction helpful
After reading everyone elses stories, I purchased all new springs(5), new spring brackets(one of mine was rusted really badly)and all new wear pads(two sets of 3pcs each). The rusted spring bracket was the most time consuming as the screw was rusted into the bracked so I had to drill it out. Other than that, the actual spring replacement was easy. Took maybe 10 minutes. The wear pads were another story. I'm a pretty good mechanic and I had a bit of a struggle getting the old pads out. I used a long, flat head screwdriver to pry them out. Once they were out the new ones weren't too tough to get back in. Took about 20 minutes all together. I stongly recommend watching the video on removing the washer cabinet first. It will save you some time. Acutally, watch the videos on all of the parts to simplify the process. Oh and by the way, all of my washer problems are gone. Well worth my time and $70 in parts. Good web site!
All Instructions for the 4KMTW5755TW0
76-90 of 303