Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 4770 > Instructions

4770 Hoover Range - Instructions

All installation instructions for 4770 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 4770
31-45 of 100
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Grease filter needed replacing

  • Customer: Freda from Elizabethtown, NC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 4 people found this instruction helpful
Remove old filter- put in new filter. EASY!!!!!!!!

Element in oven burned out

  • Customer: Eric from Bliss, NY
  • Difficulty: Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I had to use a mirror and flashlights to see in the back of the oven to replace the screws in the new element. It was very close quarters and difficult to see behind element plate.

not a prblem,just necessary to replace

  • Customer: Peter from Wilson, NC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
even though these sre washable filters it's still necessary to change them after so much time

burned oven bulb

  • Customer: Ivanka from Atlantra, GA
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 3 of 8 people found this instruction helpful
The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.

oven light burnt out

  • Customer: William from Schwenksville, PA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 8 people found this instruction helpful
1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes

Two burner switches had broken

  • Customer: John from Seguin, TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 1 of 3 people found this instruction helpful
Turn off elec. power at breaker box. Check twice. Removed burner switch cover. caarefull remove wires from switch, note with color to which terminal remove nut on switch replace new switch replace wires to switch, replace cover turn on power. ready.

Element quit working

  • Customer: Alyce from San Antonio, TX
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 3 people found this instruction helpful
Ordered the part. It arrived in about 4 days. Took a screw driver and in just a few minutes, it was working again. BINGO

light bulb went out in my oven

  • Customer: Janet from Ada, MI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 6 people found this instruction helpful
My husband took the plastic cover off and took out old bulb and screwed in the new one. Then put the cover back on.

front burner would only work on high

  • Customer: william from cairo, IL
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Installed the part------very easy

Bad switch

  • Customer: Merwyn from Kingsport, TN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 1 people found this instruction helpful
As stated on order.

Heating coil/ element gave out.

  • Customer: Tom from Rochester Hills, MI
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 1 people found this instruction helpful
I turned off the power first. Then I removed the element by taking out the three screws. The oven was quite old so getting the screws out took a little extra effort. Installation of the new element went easier. I was pleased with how soon the part arrived after I ordered it.

needed new grease filter

  • Customer: Mary from Anna Maria, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Removed old grease filter,replaced with new grease filter. No tools needed.
I ordered the grease filter on Tuesday and it arrived at my door on Wed.
Best experience ever ordering a part, I will definitely use Part Select again and have already recommended it to friends.

uneven/intermittent burner heating

  • Customer: Kelly from Alameda, CA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Wrench (Adjustable)
  • 0 of 1 people found this instruction helpful
shut circuit breaker, remove two screws, lift knob panel, move wires to new switch, remove and replace switch, clean surface

cooks "high" on all settings

  • Customer: Robert from Jacksonville, FL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 1 people found this instruction helpful
Turn off the power. Remove 2 screws (in the blower compartment) and lift up the control panel. Release the switch by removing the fastnut. Unplug each wire from the old switch and place it in the cooresponding lug on the new switch. Screw everything back together and cook.

One electric range top burner element quit heating

  • Customer: A E from Houston, TX
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 1 people found this instruction helpful
Kill power to range unit at the breaker. Remove 2 screws on back of center control panel. Lift control panel up and toward rear of unit. Unscrew retainer nut which holds switch in the control panel. Carefully note wiring connections, and unplug all 5 wires from switch with pliers. Remove old switch. Reconnect all wires to new switch. Reattach switch to panel with retainer nut. Replace control panel in range with screws. Turn on power.
All Instructions for the 4770
31-45 of 100