4760 Hoover Range - Instructions

Just a couple of minutes to left off the cover grid, left out the old filter and drop in the new one.

Just placed it at the filter location. Liked the ring feature on the filter for ease of removal for cleaning. My previous ones didn't have such feature. Thank you for filling my order. I bought an extra filter for the future. I'm a big user of my Jenn-Air range. I may soon be needing to replace my griddle. Will be contacting your company then.

Locate and open appropriate breaker to kill power to the range. (very important if you intend to see tomorrow).

Pull off the control knob.

Remove 2 screws that hold in control pannel.

Lift out the control pannel to the extent that the wires will let you. (2-3 inches)

Remove the nut that holds the switch/controller in the pannel.

Remove the wires one at a time and reconnect them to the new switch. Make sure to connect them the same way on the new switch.

Re-install the switch in the pannel.

Re-install the pannel in the stove.

Close breaker and test burner contol.

I simply lifted off the grille in the center of the stove, pulled out the old filter and dropped the new one in. It sits at an angle (right side down, left side up) rather than slotting in to a particular spot.

Took the old knobs off and replaced them with the new!

Our oven is at least 30 years old and the parts are not even available through the manufacture anymore. A new stove would cost well over $1000.00. Jen airr is the only down draft stove available. So the repair was much more affordable that the alturnative. So thank you to part select for providing this service. The repair was simple. This is coming from a 36 year old female who has been around electrical work, but never done any myself. My husband was out of town and I felt I could do the job. I first made sure I had another adult present. I turned off the power to the oven. I then removed the visible screws to the element plate (2 on top and 1 in lower middle). I then pulled the element out enough to get behind the plate and feel the screws that were connecting the wires to the element/ground. Again 3 total. The oven space is very small and difficult to work in. I had to do a lot by feel. Once the old element was free I just exchanged it for the new one and reversed the process, making sure all the wires were tight. I then turned the power back on. Turned the oven on, it smoked lightly for a moment and turned red hot. Over all it was extreemly simple.

It's wonderful to get accessories for this 20 year old Jenn-Air. I love it and now it looks like new.

Well, since the circuit breaker blew when the fan switch burned out, I was hoping to get a new counter-top range out of this. But, no such luck. My son opened up the control module (2 screws under the fan grill) and found the problem. Then I decided that if I needed to replace ONE part, I'd replace ALL of the parts that didn't work and were worn out.
First I turned off the breaker all the way, then, since the module was open anyway (it pulls out about 2 inches), I only had to remove the old fan switch using the socket set, and replace it, wire-for-wire with the new one. The flange needed to be filed down a bit because it was wider than the original, but not a problem to do. I had to use the original nuts to hold in the new one. The new ones are smaller. Just used the socket set in reverse
....done!
The burner switch and knobs were a little more of a problem but only because ordering them didn't follow the rules...I needed series 3 parts, even though I had a "Run 01" range top. With the help of a very nice customer service rep, I got the correct parts the next day and replaced the burner swich the same way...used a socket set to loosen and remove the old switch and connected the new one wire-for-wire, and again needed to use the original washer and nut. (The wrong model that I initially received had a new washer and nut in the bag with the switch.) But, again, no problem.
The control knobs just pull off and push on...simple.
Now that I had a nearly new range top, I spent another 2 hours REALLY cleaning it (Dawn Power Dissolver is GREAT!). Looks almost like new! I guess I won't be getting a new range top for another 22 years now.....

After searching on the internet for a very long time, we were almost ready to order the screws "blind" (no picture) from Sears for almost $10.oo per screw. Then I stumbled onto this website and found exactly what I was looking for, with a detailed description AND a picture!! Not to mention a price that was two thirds less than Sears..for TWO screws. Now the oven door is secure and we are no longer on our search for the right screws.

following the directions in the package and on-line, this repair was easier than i could have imagined. changing out these two parts took less than 15 minutes.

Turned off electricity at the circuit box. Removed four screws from panel cover that housed the switch. disconected the wires from the old switch and replaced the old switch with the new one reconected the wires put the panel cover back on. voila done.

Made sure the circuit breaker was off. Labeled the wires and then disconnected them. Removed the old switch.
Ordered the part using the diagram on-line, very easy to identify part and order it. Part arrived earlier than expected using standard shipping.
Reconnected wires using labels taped on the wires. Turned on the breaker and it worked.

knobs fit perfectly

Shut off the breaker! Removed down draft grill. Removed two phillips head screws and lifited switch plate out. Removed switches (2) and made wiring diagram as I went. Looked up Jenn-Air on line and ordered parts. Lost wirihng diagram in the process but still had two switches wired . Replaced all four switches. Everything working great. However while I was waiting on switches to arrive, somebody at the house was fooling with the switch plate and broke the on red indicater lens so now I'm ordering that. Oh well....

First pulled the two screws holding the control with the switches. Then I unscrewed the nut holding the 6" burner switch and disconnected the wires on the switch and replaced the switch with the new one. Replaced the control unit in the range top and tested the repair.