4760 - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Oven element burned out
The only trouble I couldn't remove the screws that held the wires to the element, so I cut the wires as close to the end as possible and attached new hardware. After that was done it was simple to reinstall the new element. Turned the power back on. Turned the oven on and it worked like new.
Parts Used:
-
Eugene from Satellite Beach, FL
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
0 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
bake element not heating up
removed element and tested wirh ohm meter. No reading telling it was bad. Tested voltage from supply wires. Voltage correct. Ordered new element which can in 2 days. Installed-tested- problem solved. 2 scres connect element.
Parts Used:
-
john from chatham, MA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
0 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The stem of one of my burner switches broke off so I had to replace the switch.
Replacing the switch was very easy. First I unplugged the range to be sure there would be no electrical power to the switch. Then I removed four screws to remove the switch cover plate (located above the oven door). I disconnected the wires from the pin connectors on the broken switch, then removed the switch by removing one hex nut. The new switch was installed by reversing the removal procedure. Took about 15 minutes total time.
Parts Used:
-
John from Fulton, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers, Wrench (Adjustable)
0 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
uneven/intermittent burner heating
shut circuit breaker, remove two screws, lift knob panel, move wires to new switch, remove and replace switch, clean surface
Parts Used:
-
Kelly from Alameda, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers, Wrench (Adjustable)
0 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bad switch
-
Merwyn from Kingsport, TN
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers, Socket set
0 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
parts fine,
-
MARY from ELK RIVER, MN
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
front burner would only work on high
-
william from cairo, IL
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
0 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The filter in the grill section of my stove fell apart.
I simply removed the old filter and replaced it w/the new filter. It came in record time and I'm very pleased w/the service I received.
Parts Used:
-
Beth from Dunkirk, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
the original grease filter was worn and falling apart
Removed the old filter from the top of stove and put the new one in. Took about 10 seconds.
Parts Used:
-
Barbara from Medfield, MA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
In cleaning the cooktop water/cleaner leaked into the fan switch. This blew the switch.
First, electricity was shut off from stove. Then two screws that holds the element into place was removed. I pulled element out about 3to8 inches and disconnected the wires to the damaged rocker switch. A new rocker switch was installed. Replaced element back into position and replaced the two screws. Job was finished within 10-15 minutes.
Parts Used:
-
Dolly from Cumberland, KY
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers, Socket set
0 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
I Destroyed My Grease Filter In The Dishwasher And It Just About Disintergrated.
I just had to drop the grease filter into the slot. It took less than a second. But what I am really pleased with is that it took less than a day and a half to get the part. I ordered it on thursday morning. It was shipped on thursday afternoon and in my driveway by friday noon!!! Wow!!! How great was that!!!!!! The fastest service I've every had for anything!! Bravo!!!!!!!! To all your workers!!!!! Rrm
Parts Used:
-
Rosetta R. from Jamaica Plain, MA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
1 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
lower element was burnt out
-
JOSEPH from WARRENTON, VA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
0 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Grease filter broke
-
Charles from Leighton, IA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Wanted to replace old grease filter
Removed old filter, dropped in new filter. A breeze! What was best of all, is that Parts Select shipped the filter immediately and it arrived within just a day or so! Well done!
Parts Used:
-
Christine from Pembroke, VA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Filter was old and discolored.
The new replacement grease filter came without damage and it was a simple task of removing the old and setting the new in it's place. No tools were required.
Parts Used:
-
Robert from Warroad, MN
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!