Models > 41771712512

41771712512 Kenmore Washer Dryer Combo - Overview

Sections of the 41771712512

[Viewing 5 of 5]
Keep searches simple, eg. "belt" or "pump".
Drum Support Bearing – Part Number: 131825900
Drum Support Bearing
★★★★★
★★★★★
(19)
PartSelect #: PS418807
Manufacturer #: 131825900
If your dryer does not tumble, will not start, is noisy, or is leaving marks on your clothing, you may need to replace the drum support bearing. The drum is supported at the rear by a bearing, which a...
$8.96
  In Stock
Order within the next 11 hrs and your part ships today!
Drum Glide - White – Part Number: 137513300
Drum Glide - White
★★★★★
★★★★★
(15)
PartSelect #: PS5574052
Manufacturer #: 137513300
This white drum glide is used in a clothes dryer to ensure the front of the dryer drum is supported as it does rotations. *Please note: these are sold individually, however there are two of these in y...
$40.21
  In Stock
Order within the next 11 hrs and your part ships today!
Dryer Lint Screen – Part Number: 5304516871
Dryer Lint Screen
★★★★★
★★★★★
(25)
PartSelect #: PS12585473
Manufacturer #: 5304516871
This dryer lint screen is for laundry centers. Dryer lint screen captures lint and debris from the exhaust air flowing from the dryer. Follow the instructions in the owner's manual when installing this part.
$43.42
  On Order
Door Catch – Part Number: 131658800
Door Catch
★★★★★
★★★★★
(18)
PartSelect #: PS418433
Manufacturer #: 131658800
The door catch on your dryer is an important part as it keeps your dryer door closed, in order to ensure no air or clothes can escape. This part works by holding the door strike, which allows the door...
$58.17
  In Stock
Order within the next 11 hrs and your part ships today!
Multi-Rib Drum Belt – Part Number: 137292700
Multi-Rib Drum Belt
★★★★★
★★★★★
(12)
PartSelect #: PS3408299
Manufacturer #: 137292700
The multi-rib drum belt is also known as a drive belt and is a part for your dryer. The function of the drum belt is to attach to the motor pulley. It will then spin the drum as the motor rotates. Ove...
$20.15
  In Stock
Order within the next 11 hrs and your part ships today!
Lower Front Felt Seal with Adhesive – Part Number: 5303937183
Lower Front Felt Seal with Adhesive
★★★★★
★★★★★
(6)
PartSelect #: PS832645
Manufacturer #: 5303937183
The lower front felt seal with adhesive, also known as a drum felt seal, is used in dyers and allows the drum to easily glide on the front panel. For this repair project, you will need the following t...
$29.90
  In Stock
Order within the next 11 hrs and your part ships today!
M Series Ignition Coil Kit – Part Number: 5303931775
M Series Ignition Coil Kit
★★★★★
★★★★★
(24)
PartSelect #: PS470049
Manufacturer #: 5303931775
This kit contains two coils, one is a two-wire secondary coil and the other is a three-wire booster coil. Both coils in the ignition coil kit should be used together in the clothes dryer. Some of the ...
$35.04
  In Stock
Order within the next 11 hrs and your part ships today!
Dryer Drum Bearing Bracket – Part Number: 131724301
Dryer Drum Bearing Bracket
★★★★★
★★★★★
(2)
PartSelect #: PS12579101
Manufacturer #: 131724301
This drum bearing bracket is for dryers. Drum bearing bracket holds and supports the drum bearing
$10.50
  In Stock
Order within the next 11 hrs and your part ships today!
Ball Hitch – Part Number: 131777700
Ball Hitch
★★★★★
★★★★★
(1)
PartSelect #: PS418736
Manufacturer #: 131777700
This ball hitch provides support to the drum located at the back wall of the dryer. This allows the drum to spin. The bearing may have gone bad and you might notice that the ball is cut off. The ball ...
$69.82
  In Stock
Order within the next 11 hrs and your part ships today!
Front Upper Felt Seal with Adhesive – Part Number: 5303937182
Front Upper Felt Seal with Adhesive
★★★★★
★★★★★
(3)
PartSelect #: PS832644
Manufacturer #: 5303937182
The upper felt seal for your dryer is attached to the top edge of the drum support area, and is held there by a high temperature adhesive. It creates a seal where the dryer door opens and closes, so t...
$24.71
  In Stock
Order within the next 11 hrs and your part ships today!
Screw-In Plastic Leveling Leg – Part Number: 134548800
Screw-In Plastic Leveling Leg
★★★★★
★★★★★
(4)
PartSelect #: PS1152204
Manufacturer #: 134548800
This is a screw in leveling leg for your washing machine. It supports the appliance by screwing in place to create a stable and flat surface. Take note that you are able to adjust the height of your a...
$25.68
  In Stock
Order within the next 11 hrs and your part ships today!
Door Strike – Part Number: 5303207102
Door Strike
★★★★★
★★★★★
(7)
PartSelect #: PS455020
Manufacturer #: 5303207102
The door strike is attached to the door of your dryer and holds the door closed. If your dryer door is not closing, this might be due to the door strike needing to be replaced. This is a simple repair...
$21.75
  In Stock
Order within the next 11 hrs and your part ships today!

Questions And Answers for 41771712512

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

Common Symptoms of the 41771712512

[Viewing 10 of 10]
Noisy
Fixed by
these parts
Show All
No heat or not enough heat
Fixed by
these parts
Show All
Will not tumble
Fixed by
these parts
Show All
Door won’t close
Fixed by
these parts
Show All
Marks left on clothes
Fixed by
these parts
Show All
Will Not Start
Fixed by
these parts
Show All
Takes too long to dry
Fixed by
these parts
Show All
Shuts off too soon
Fixed by
these parts
Show All
Leaking
Fixed by
these parts
Show All
Too hot
Fixed by
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
squeeking like crazy
well, i started at the top and worked my way down. by taking the top off, it gave me more room to get the dryer tub out. took the two screw`s out of the vented plate on the back of the machine to undo the belt. this is a stackable washer-dryer combo, so next i took off the white plate on front between washer & dryer. took off the control panel, unpluged it, then took dryer door front off. then removed the two screw`s that hold that bracket on ,in the back of dryer, pulled the drum out & replaced the belt, but before replacing anything i took the shopvac to it , there was alot of lint in there.when replacing the Grounding Ball Clip & Grounding Ball, i took a one inch by two inch magnet and used it to hold the Grounding Ball & Clip in place so i could get the two screws started in the Drum Support Bearing & Bearing Bracket. after installing that i put the shaft in place & lined the dryer tub up with the 3 screw hole`s ,and boom, bang, pow...nothing to it. it`s easy...parts came very fast....Thx PartsSelect.com...i`ve told all my friend`s about PartsSelect
Parts Used:
Multi-Rib Drum Belt Grounding Ball Clip Grounding Ball Drum Support Bearing Ball Hitch Dryer Drum Bearing Bracket
  • Steve from Wheelersburg, OH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers, Wrench set
126 of 144 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer would heat initially then cool down
The top of the dryer was easily removed by prying the front up with a screwdriver then tipping it back and off of the mounting brackets. Then the front of the dryer was removed by unscrewing a single screw on each side that held the front to the side panels then pulling the front away from the dryer. Once the front was off, the coils were easily accessible on the bottom left side. A metal bracket held the coils on and was somewhat tough to get the two screws removed on it as they were stuck, but once they were removed the coils easily came out and I was able to replace them in minutes. The whole job took 15-20 minutes and I now have a dryer that heats through the entire drying cycle.
Parts Used:
M Series Ignition Coil Kit
  • Brett from Monticello, MN
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
90 of 102 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Felt pulling apart and glide not secured
For the glide, I want to advise people that to replace the entire glide you need to order two front drum glide parts as each is only half.

First, unplug the dryer. Then, open the top so that you can get access to the work area. On each side of the inside front, there is a screw that connects the front panel to the side panels. Unscrew those screws and pull the front panel until it disconnects from the side panels. Be careful as there are wires that are secured to the bottom of the top inside lip of the front panel. One set of wires goes to the light bulb in the dryer door. You don't need to disconnect the wires, but be sure you don't damage the wires by pulling the front panel too far away from the dryer.

Once you have the front panel out of the way, you can see the front drum glide. In my case, one half was loose as the plastic plugs that pop into recesses to hold the glide in place had broken off. Remove the damaged glide section and replace it with the new section, popping the plastic plugs into the recesses. Don't be afraid to slap the glide to lock the plugs in place.

For the felt, I cut the part of the old felt that was pulling away from the front panel. I then used a flat-head screwdriver and wire brush to remove as much of the old adhesive as I could. Then, using the high-heat adhesive that came with the new felt, I put a generous amount on the front panel where the felt needed to go. I used a toothpick to spread the adhesive to get maximum area coverage. I let it set for a minute or two, and then placed the new felt. I used small clamps to keep the felt in place until the adhesive had time to bond. I only kept the clamps in place for 10 minutes.

Once I removed the clamps, I let the felt continue to adhere to the front panel for 24 hours before reassembling the dryer. Again, be careful of the wires connected to the front panel as it appears very easy for them to be pinched or cut when putting the front panel back in place.

When the dryer was reassembled, I plugged it back in and have had no more troubles.
Parts Used:
Lower Front Felt Seal with Adhesive Drum Glide - White
  • Timothy from Pensacola, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
72 of 78 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!