Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 41748102701 > Instructions

41748102701 Kenmore Washer - Instructions

All installation instructions for 41748102701 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 41748102701
196-210 of 283
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Washer was leaking

  • Customer: Donald from Burlingame, KS
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I took the front and back off the machine. Removed the old pump by taking out a couple of screws. Put the new pump back in and put it back together. Works fine now.

Vibrating Washer During Spin Cycle

  • Customer: Stephen from Sister Bay, WI
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required:
  • 0 of 0 people found this instruction helpful
The video is very good. I have a stacked unit and didn't want to remove the dryer. It was difficult (but not impossible) to get the pins removed and replaced. I made a removal tool by drilling a 15/32" hole into the end of a 1"x1" piece of wood. Taping on this closed the pin safety and pushed it out.

Went into pause mode when starting

  • Customer: Fred from Wakefield, RI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Completed by my wife on line instruction video

Both shock absorbers were not working properly

  • Customer: Harold from East Peoria, IL
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
The video was helpful and gave good ideas to look for, it was harder to reach the pins holding each end. I used a 6-8 inch dowel rod to remove and replace the plastic pins. First time always takes longer than advertised but I wasn't in a big hurry.

Error Code E43 - door lock problem - no spin

  • Customer: Allan from Charlestown, MA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Removed retaining band around door boot and prized-off boot on left side to access door lock - simple screw driver replacement job. Deleted last error code. BUT - washer worked again for several days, and now code E43 is back and won't spin - problem is intermittent - so suspect it is NOT the door lock, but a wiring or control board problem. Ongoing.

Would not go into spin cycle

  • Customer: Jim from Dyersburg, TN
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Took off top. Removed 2 screws on Door Lock Assembly and replaced.

Door lock mechanism broke and washer would not run

  • Customer: SCOTT from SALINE, MI
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
You must remove the top of the washer with screws on rear of washer. Top slides forward to remove. Once top is removed you can reach door lock mechanism from the top. Two screws must be removed from the front of the washer where lock enters mech. You can grab the mechanism from above by the wires that run to it. Undo wiring harness and insert new mehanism. Slide into place and attach in the front of washer with screws. This job is easy and can save you a lot on repair bills!

washer failed to drain

  • Customer: Gerard from upper sandusky, OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
sucked out remaining water with shop vac. took off lower front panel, two screws. took off back panel, six screws. diconnected drain hose from pump,some addittional water drained out, sucked up with shop vac. disconnected tub drain from pump, more water, shop vac. unplugged two wires from back of pump, removed two screws holding pump, removed pump, put in new pump, reversed procedure. Done!

Washing machine stopped draining

  • Customer: Peter from Natick, MA
  • Difficulty: Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers, Socket set, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
The machine is very heavy. It was setup in a tight elevated drain basin on the top floor of the house. I could not move it off the drain basin onto the floor, so I built a platform and shifted the machine on to the platform. Once the machine was on the platform, I located an access panel on the back of the machine, removed it and found the pump. Part Select indicated that a drainage problem was probably the pump or the filter, so I bought both. I removed the pump and found a finishing nail had passed through the filter into the pump and jammed the pump's propeller. So, I replaced the jammed pump with the new pump. The existing filter seemed OK and a lot of trouble to remove, so I left it in place. I re-assembled the machine , pushed it back into place and it has worked ever since. Lessons learned: the clamps that hold the inlet and output hoses to the pump are really difficult to remove and replace without the right tool. Don't leave finishing nails in the pockets of your dirty work pants; be ware of very sharp edges on the bottom the machine and consider turning the machine over if you need to replace more than just the pump.

door strike broke while moving

  • Customer: Shari from Raleigh, NC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
very easy, just put in the 2 screws and it was fixed..

Would not fill with water

  • Customer: clyde from tunkhannock, PA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
Installed New shock absorbers and new door strike. The existing broken shock absorbers caused the drum to oscillate and pull wires from door lock switch.

Door Strike Broken off in lock

  • Customer: Linda from Parkersburg, WV
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The end of the door strike had broken off in the lock. The door strike itself went on in just a few minutes. The time consuming part was getting the piece that had broken off out. After trying with tweezers to get it out, we took the lock off the machine and finally got it out. So....if the door strike looks damaged or isn't shutting properly, replace it before it breaks off inside the lock. We were pleased with how quickly it came. We ordered it Sunday evening and it came Tuesday morning.

the washer would not spin out all the water

  • Customer: Chris from Troy, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I took off the bottom cover by removing the two screws on the bottom cover. The shock absorber was completely broken off from its bracket. I pulled the plastic pin on the top and bottom of the shock absorber and installed the new shock. The machine works perfect again spinning out all the water. With the broken shock absorber the drum will shake violently and the machine shuts down. It makes it appear to be an electric control problem.

Door Lock and switch didn't work

  • Customer: Christine from Bedminster, NJ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Using a youtube video, (which might have actually been related to parts select), the door lock replacement went smoothly AFTER I couldn't SEE the SPRING around the rubber boot, as the spring was the SAME color and with a little bit of dust on it, was indistinguishable. As soon as I found it, the rest was fairly simple. I MIGHT even try replacing the moldy boot on these stupid front loaders...I paid for overnight shipping as I also had Geek squad guys on hold for repair, and needed to know fast, whether or not this would do the trick. HOORAY!

shock absorber s were worn out and let the tub vibrat badley when it went into spin

  • Customer: arthur from lake mary, FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I watched a tutorial online (don't believe it he only showed the easy side) you have to hold the clip on the nylon pin and drive it out on both ends of the shock. on the rite side the lower pin hits on the back side and wont come out far enough to release the shock,i had to get on the backside and cut the pin off(thankfully their was a spare pin in the kit,you also have to disconnect a hose in front of the top pin on the rite side,i don't know how you would ever get this pin out if you ever had to again as you have to drive it in backwards. I neglected to tell you this was a top loader and the fron lower panel gives you access to these shocks.
All Instructions for the 41748102701
196-210 of 283