41739022891 Frigidaire Washer - Instructions

Removed the the two screws holding access panel on the bottom front. Shocks use two plastic retaining pins on each shock. Used a screwdriver to push down on the locking tab on the plastic retaining pin ant pushed out. One of the pins is behind the water pump and a bit harder to access. I used a socket with an extension to push it out. installed new shocks with old pins and was back in business. Shocks go in a certain way so be sure to look at the instructions that come with the replacement shocks. Note: the replacment shocks that came don't look anything like the originals. Originals looked more like an automotive shock. Also as both shocks were broken, I ordered two, not knowing that they come two to a package. When you order that is not clear. So now I have an extra set, which might not be bad to have on hand. Kit also comes with an extra pin in case you break one.

First I removed the two screws holding the front panel on and removed the panel. The hose is held on by two spring clips and a hose clamp. After getting those out of the way, I removed the damaged hose and slid the new one into place and fastening it down with the aforementioned clips and clamp.

First I turned off the breaker to the washer.

Then I removed the drain pump motor, saw that it was broken, and ordered a new one with expedited shipping. It was delivered about 36 hours later.

I should have used my wet/dry vac to suck out all of the water remaining in the drain lines. Because I didn't, nasty water dripped all over my laundry room. Lesson learned!

The part arrived at 2:20. I had to pick up my kids at school at 3pm. I wasn't sure I'd have time, but I tried anyway. I first removed the screws holding the entire pump assembly to the floor of the washer. Then I attempted to remove the clamps holding the three hoses onto the pump / motor assembly. I tried with regular pliers for about 10 minutes and finally realized I needed locking pliers. Mine are missing, but I have a stone mason doing a project at my house. I borrowed his and immediately had the clamps loosened. I slid them back onto the hoses, inserted the pump motor into each hose one by one, and reattached the clamps.

I ran a little water into the washer, checked to see that it didn't leak upon draining, then started a load and left to get my kids from school.

This was a very easy repair. The part was $75 plus about $20 for the expedited delivery. The Sears service call would have been $65 just to walk in the door PLUS whatever they would have charged me for the labor and the part. I am guessing I saved over $200.

The worst part was the gross water remaining in the drain lines. This would have been easily avoided if I'd just taken the time to get the shop vac. Learn from me and don't skip this step!!

disconnected the power cord,removed two screws on lower front edge of machine, removed lower front cover. Got the wet vac ready to suck up the water in the rubber boots when I took the clamps off. Disconnect the pump wires, and two bolts that mounted the pump. wrestled off the boots, and cleaned out the junk in the bottom of the main boot, sucking up water as the boots came off. then reversed the process. Not bad at all. Makes you want to double check for coins so they don't destroy the pump impeller.

Watched video which was very helpful

Please note that I went online first to get an idea of what was involved.
I removed the back panel using a cordless drill w/attachment for the screws. Then the top. The directions that I received online was very helpful, but I didn't remove the whole tub assembly. I don't recommend doing it my way, but it can be done without removing the front or the whole tub assembly. After the motor and the big pulley was removed, I removed the bottom "shocks". I then took out every one of the cap screws that hold the 2 halves together. When that was done the two halves were loose. I then supported the bottom and took out the two springs. The back half came out quite easily then. It is then necessary to use a mallet to remove the inner drum from the bearing and back half of the tub. I cleaned and inspected the "spider" which was fine except it had old soap in it. Then using a dremel tool with a plastic brush I cleaned/polished the shaft of the inner tub. The new rear shell fit perfectly. Supporting the bottom of the front half of the tub, I then placed the back half assembly (with the pulley replaced on the shaft) in proximity and started the cap screws. It is weird how the 2 halves don't want to stay in correct alignment, but it can be done. After I got most of the top screws in, I used a ratchet wrench to tighten them to almost where the 2 halves were touching. That helped with the alignment process. When all (Ibelieve there are around 17 screws) were started and the 2 halves were aligned, I then started at the top and tightened to a loose fit. The second time around I tightened to semi tight. At this time I could put the springs back on (greatly improves ability to reach the bottom screws). The third time around I put them all tight. Every thing went back on without a problem. I attached water and power to the unit and ran a cycle with the top off and checked for leaks. That's it.

Front-loading Frigidaire washer made by Electrolux:
I removed the one phillips screw that secures the drum, but found the vane did not slide toward the front as I'd read it should. Nor was I able to squeeze the base to release it. I ended up using a rubber mallet and screwdriver to spring the snaps at the bottom of the vane. Once I had two of these on the same side out, I was able to slide the vane forward and remove it. Turns out there was a metal tab, part of the drum, bent into the vane so it couldn't slide for removal. I bent this tab down even with the drum surface, and the new vane slid in easily.

After moving machine to an area that allowed easy access to the unit, disconnected the water supply hoses from the inlet valve.
Removed the two screws that keep the back in place, removed the clips that keep the top in place, moved the top over far enough to get the valve out. Removed the screw that keeps the inlet valve in place, disconnected the power supply to the valve, Pulled valve out in order to remove the water outlet hose. Repalced with new vale, and reversed order to install. Works just fine now.

Checked problem on-line and discovered it was the water inlet valve. Matched the part on part select. Com. Finding the part was very easy. Part select had a grid behind the picture to help determine the size and pictures from all sides. Removing the old part, matching it, and replacement took a total of 30 minutes. I now have clean clothes.

Once I figured out that the shocks were broken it was very easy to fix. Remove back panel first. Then remove the control box on bottom left corner to gain access to the left shock. Pinch the locking mechanism on the plastic locker bolts and remove the four bolts from both shocks. Replace with new shocks and replace control box and back panel. It probably took more time moving the washer to where I could work on it then it did to fix it. Works like new.

Vibration/Shock: remove front cover, to remove the shocks depress the tab on the locking pins and push out. Install new shocks and pin in reverse order.

Pump: Disconect power, remove front cover, slowly remove clamp from discharge side of pump and use a sponge or rag to collect water. About one pint will remain in the upper hose. Remove the upper hose after draining. Unplug the power supply to the pump and remove two screws securing the pump to the floor of the washer. Install the new pump and conect wire and hoses.

The illustarated parts break down on the Part select web site was an awesome resource. It identified the exact part that was damaged by part number and comprehensive drawing. The part was ordered utilizing the drawings and on my doorstep within two working days, regular ground shipping. The securing pins were removed from the damaged shock absorber by driving them out with a screw driver (used in place of a drift punch) and a rubber mallet. The new shock absorber was placed in position and the securing pins were installed easily by hand and were securely in place when an auditable click was heard from the securing pin when fully engaged. The shock absorber kit came with an additional securing pin in case one of the original pins were damaged. The replacement part was of superior quality to the original.

The previous posts made it dead easy - remove screws at the back holding top in place; slide top back; remove screws holding door latch assembly; disconnect three plugs, and connect new part. Replace fastenings, done! Throw up hands and wait for the official time;)

I unplugged the washer. Then I unscrewed the two screws on the back, top edge of the washer. and lifted the top off. Next I unscrewed the door lock/switch assembly, reached down in the machine from the top and pulled the switch out. As I unplugged each one of the three plugs from the bad part, I plugged them into the corresponding connections of the good part. Then I screwed the switch back into place, replaced the top of the washer and screwed it back on. I set the washer spin and cheered madly when it went into spin mode. The hardest part was actually turning the screws because I'm a small woman and my hand strength is not what it used to be. But really there was nothing difficult about this repair.

Clear a work space, set up bins for parts, there are a lot of them, so upon removal, put all parts in same place (motor bolts in same box as motor, etc), use a digital camera to capture where everything goes.
Remove back, remove front lower access panel. Remove all plumbing from tug. Remove belt and large pulley from back (tap gently with mallet around perimeter to remove). Unhook motor wire connector, cut the zip tie. Remove the motor (4 bolts). Separate the front seal, remove the shock absorbers (use a deep socket to push in plastic tabs). Now the fun part, carefully tilt the washer back to the floor (2 people, it is heavy), while supporting the tub, to keep it from over swaying (I cut a 2x4 to size, put it between the tub and the lips of the side walls to keep it in place).
You should now be able to remove the springs (leverage them out with old screw driver), clear all parts from the tub. You can then lift the washer housing from the tub vertically. You should then be able to access the tub clearly. Remove the counter weights, set aside carefully, they are fragile. Remove the bolts holding the tub together.
Tap out the tub.
Reverse the process to put back together. Careful not to over tighten the bolts on counter weights or motor.