41739012890 Frigidaire Washer - Instructions

Removed the the two screws holding access panel on the bottom front. Shocks use two plastic retaining pins on each shock. Used a screwdriver to push down on the locking tab on the plastic retaining pin ant pushed out. One of the pins is behind the water pump and a bit harder to access. I used a socket with an extension to push it out. installed new shocks with old pins and was back in business. Shocks go in a certain way so be sure to look at the instructions that come with the replacement shocks. Note: the replacment shocks that came don't look anything like the originals. Originals looked more like an automotive shock. Also as both shocks were broken, I ordered two, not knowing that they come two to a package. When you order that is not clear. So now I have an extra set, which might not be bad to have on hand. Kit also comes with an extra pin in case you break one.

Vacuum all water possible from the tub. Remove the front panel to provide access to the pump. remove the pump from the washer, but leave the hoses attached lift the pump into the bucket, and remove the clamp from one of the hoses. clip the hose partially off the fitting and drain water from the rest of the tub and hoses. It may be necessary to reattach the hose during this draining process to keep from overflowing the bucket. When the lines are empty, remove the other clamp and remove the hose from the pump. Be sure to disconnect the pump and check the hoses. I have found a sock in the tub drain line twice, which either stopped the line, or blocked the impeller. replacement of the pump is the reverse.

First I removed the two screws holding the front panel on and removed the panel. The hose is held on by two spring clips and a hose clamp. After getting those out of the way, I removed the damaged hose and slid the new one into place and fastening it down with the aforementioned clips and clamp.

Watched video which was very helpful

I had to "spin" the leftover part of the knob with a pair of pliers.

I then spun the new knob on and that was it!

I was a hero with my wife and it didn't take but a couple of minutes.

Please note that I went online first to get an idea of what was involved.
I removed the back panel using a cordless drill w/attachment for the screws. Then the top. The directions that I received online was very helpful, but I didn't remove the whole tub assembly. I don't recommend doing it my way, but it can be done without removing the front or the whole tub assembly. After the motor and the big pulley was removed, I removed the bottom "shocks". I then took out every one of the cap screws that hold the 2 halves together. When that was done the two halves were loose. I then supported the bottom and took out the two springs. The back half came out quite easily then. It is then necessary to use a mallet to remove the inner drum from the bearing and back half of the tub. I cleaned and inspected the "spider" which was fine except it had old soap in it. Then using a dremel tool with a plastic brush I cleaned/polished the shaft of the inner tub. The new rear shell fit perfectly. Supporting the bottom of the front half of the tub, I then placed the back half assembly (with the pulley replaced on the shaft) in proximity and started the cap screws. It is weird how the 2 halves don't want to stay in correct alignment, but it can be done. After I got most of the top screws in, I used a ratchet wrench to tighten them to almost where the 2 halves were touching. That helped with the alignment process. When all (Ibelieve there are around 17 screws) were started and the 2 halves were aligned, I then started at the top and tightened to a loose fit. The second time around I tightened to semi tight. At this time I could put the springs back on (greatly improves ability to reach the bottom screws). The third time around I put them all tight. Every thing went back on without a problem. I attached water and power to the unit and ran a cycle with the top off and checked for leaks. That's it.

Front-loading Frigidaire washer made by Electrolux:
I removed the one phillips screw that secures the drum, but found the vane did not slide toward the front as I'd read it should. Nor was I able to squeeze the base to release it. I ended up using a rubber mallet and screwdriver to spring the snaps at the bottom of the vane. Once I had two of these on the same side out, I was able to slide the vane forward and remove it. Turns out there was a metal tab, part of the drum, bent into the vane so it couldn't slide for removal. I bent this tab down even with the drum surface, and the new vane slid in easily.

I used the temporary knob (Vise Grip) and applied slight pressure in the counterclockwise direction and the knob turned right off and then through the old one in the garbage can and removed the new one from the plastic bag and lined up the threaded shaft to the threaded hole in the new knob and applied slight clockwise turning action careful to not cross thread the mating threads and proceded to tighten to full seating of the knob and further proceded to test the operation, proceded to wash a load of dirty laundary, works perfect.

The website saved us a huge amount of time. We thought we were going to have to take the stacking washer/dryer apart to access the panel. While searching for the part some nice person had already listed the procedure to change. Gently attach plyers to remaining knob and turn counter clock wise to remove. By knowing how this was removed it also allowed us to turn the washer on and off for laundry while waiting for the part. Just gently grab the edge of the remaining know and pull out to start. The broken knob can also be use to turn to cycle. The part was ordered on Saturday late in the day and arrived first thing Tuesday. Great service.

After moving machine to an area that allowed easy access to the unit, disconnected the water supply hoses from the inlet valve.
Removed the two screws that keep the back in place, removed the clips that keep the top in place, moved the top over far enough to get the valve out. Removed the screw that keeps the inlet valve in place, disconnected the power supply to the valve, Pulled valve out in order to remove the water outlet hose. Repalced with new vale, and reversed order to install. Works just fine now.

Checked problem on-line and discovered it was the water inlet valve. Matched the part on part select. Com. Finding the part was very easy. Part select had a grid behind the picture to help determine the size and pictures from all sides. Removing the old part, matching it, and replacement took a total of 30 minutes. I now have clean clothes.

Once I figured out that the shocks were broken it was very easy to fix. Remove back panel first. Then remove the control box on bottom left corner to gain access to the left shock. Pinch the locking mechanism on the plastic locker bolts and remove the four bolts from both shocks. Replace with new shocks and replace control box and back panel. It probably took more time moving the washer to where I could work on it then it did to fix it. Works like new.

The illustarated parts break down on the Part select web site was an awesome resource. It identified the exact part that was damaged by part number and comprehensive drawing. The part was ordered utilizing the drawings and on my doorstep within two working days, regular ground shipping. The securing pins were removed from the damaged shock absorber by driving them out with a screw driver (used in place of a drift punch) and a rubber mallet. The new shock absorber was placed in position and the securing pins were installed easily by hand and were securely in place when an auditable click was heard from the securing pin when fully engaged. The shock absorber kit came with an additional securing pin in case one of the original pins were damaged. The replacement part was of superior quality to the original.

The previous posts made it dead easy - remove screws at the back holding top in place; slide top back; remove screws holding door latch assembly; disconnect three plugs, and connect new part. Replace fastenings, done! Throw up hands and wait for the official time;)

I unplugged the washer. Then I unscrewed the two screws on the back, top edge of the washer. and lifted the top off. Next I unscrewed the door lock/switch assembly, reached down in the machine from the top and pulled the switch out. As I unplugged each one of the three plugs from the bad part, I plugged them into the corresponding connections of the good part. Then I screwed the switch back into place, replaced the top of the washer and screwed it back on. I set the washer spin and cheered madly when it went into spin mode. The hardest part was actually turning the screws because I'm a small woman and my hand strength is not what it used to be. But really there was nothing difficult about this repair.