3UMTW5955TW0 Maytag Washer - Instructions

Removed control assembly found lid switch. Had to unscrew ground wire from warsher popped clip on old switch came right out. Had to play with lid in order to remove. Popped new switch in screwed ground wire. Reinstalled control panel,plugged in and the way it went. Trouble shot with parts direct made it easy and saved me 350 dollars(new washer)

I read the experiences of others on this site and determined that the problem was probably the lid switch. Used others experience in taking the panel off and removed the old switch and inserted the new one. The post to be sure to have the lid open was good and probably saved me some time. Overall, the fix was simple and the problem appears to have been solved. The lid switch got here the day after I ordered it and that was great service. Better than paying for a service call or new washer.

Watching videos identified what parts to purchase.
Once identified - WATCH EACH PARTS VIDEO (again).
Lessons learned:
1) better to NOT tilt the washer
2) watch (more than once) and learn from the videos
3) must difficult step was loosening the tub retaining nut without having a spanner wrench (used a hammer and a short / wide blade screwdriver)
4) ended up being the tub support was not sitting properly in the suspension plate
5) cleaned and changed parts while apart
6) running as good as new

Thanks!!

The switch just snapped out of the holding section and the new part was snapped back into its place. He put the top section back on and it worked! Being a woman not knowing anything about repairing machines, I thought it went very well. I just googled my problem with the washer, it sent me to this site saying what they thought was the problem, I live chatted with someone and they confirmed the solution. I ordered the part and it came in 2 days and my husband fixed it. And now I have a working washer again. Thank you for your site. Anne

Took an educated guess it was the lid switch and after playing with the switch got it to work. Ordered new switch. The hard part was to find the model number and thanks to customer service sticking with we. we found the info and was able to come up with a part number. Re placing the switch is very easy but I had to remove the cast after trying to open the machine the wrong way. So a little body work. I also found the frame was cracked and with a fender washer on the other side of the front feet was able to fix that. Washer run great a lot is a lot quieter.THANKS!!

I decided to order the part and attempt to install it. Actually was easy. Took my time and maybe took 90 minutes. Works great.

Same as described on your video. Very simple

Old machine and vibrations are still there but weaker. Seemed to turn counter clock wise. Put a 4x4 board behind in order to stop the twisting, and keep hoses safe from vibrating and causing wear. Stays fairly stable now.

Open washer console by sliding your hand inside over the drum. There are two clips at each corner of the console. There are videos that show you how. The right clip is freely accessible. Reach behind a notch to get to the left clip. Squeeze clips to release.

Once console is open, use pliers to pull the knob shaft from inside the console. This will release the old knob. Attach new knob and secure the console.

Ordered and replaced the sensor. Fairly simple. Washer runs good now. Thank you!

Unplug the washer. Used flat blade screwdriver under each end of the control housing on top of the machine. This popped the spring clips and allowed the control housing to be lifted up and rotated out of the way. Once out of the way, lift clip on wiring harness to lid switch, then pull the harness off. Use nutdriver to remove screw holding ground wire in place. Open lid of the machine. Pinch tab on back of the lid switch and rotate the switch up and out of the machine. Insert the new switch in the same manner, making sure that the machine lid remains open until the switch snaps into place. Attach ground wire using screw removed earlier and nutdriver. Clip wiring harness back in place. Close the lid and then rotate the control housing downward, and press on both ends to re-engage the spring clips which hold it down.

Disassembled top control console and surrounding sheet metal cabinet per the video from this site. i then used a screw driver to carefully pry up each wear pad location individually and inserted the wood wedge. to about 1 1/2 inch height. rwmoved the old wear pads and popped in the new pads one by one. Closed up the unit and tested the machine . It ran like new. No more noise or viberation

replaced missing screw and pad and now machine works perfectly

The video was well made and made repair easy. I like the fact the video also showed how everything went back. The most difficult part and most time consuming for me was putting the washer cabinet or housing back on. I had a hard time lining the sides onto the slot to lock in place....the minor cut on finger sustained during the process was worth it. It saved me from buying a new washer and the whole family are happy that they don't have to wring out the clothes before putting it the dryer. Thank you!

Unplugged the electrical plug and turned off the water. Used putty knife to remove control box. Unplugged the washer lid switch. Used screwdriver to remove clips to washer cover. Removed cover out of the way. Removed clips that hold the drain hose on the washer frame. Used Pliers to open the clip that holds the drain hose on the discharge pump. (You will need to re-use this clip) Removed the bad drain hose. Installed new hose with clip to discharge pump. Clipped in new drain hose to the washer frame. Re-installed washer cover and re-clipped brackets. Re-plugged lid switch and re-installed the washer control box. Turned on the water and energized the washer. Ran a test load and checked for leaks.