3UMTW5755TW0 Maytag Washer - Instructions

After seeing video it was easy . Took everything apart tub,basket,replaced all springs. Tub wear pads. It took longer because I cleaned eveything,took my time. There was a lot of deposits on tub and outer tub also some rust . Put it all back together all nice and clean . pluged it in put it in spin cycle and the motor just hummed. I than check to see if somethig was stuck no .Pulled motor tested it with out a load and did not work. Motor start winding went. Motor died. 2n one in 7 years. So I fixed that proplem I am a new owner of a Speed Queen washer and dryer .

Watch the video on the part ordering webpage.

Took the cabinet apart really easily with Part Selects helpful video. Removed old suspension springs by removing outer brackets on two of them and by using pliers on the third one. The tub spring was totally missing. Put on two new brackets and springs with the nut driver. Then stretched the third spring into place. Replaced the tub spring by stretching into place and then put cabinet back together. All done very quickly!!! Now it works perfectly and runs very quietly.

First, unplug the unit. Remove the two screws on each side of the control panel on the back. They are located at the top corners of the unit. The base is held on by clips you press in on from the bottom. You will have to reach in over the tub and press in on clips, one each on the far side. At the left, you will be able to feel the lid switch, the clip is just to the left of the switch. It is about ½ inch wide, press firmly with your thumb. You may want to wear glove for this unless you like battle scars. Once done the control panel should hinge up. The switch is on the left side. To remove the switch, I first detached the wire harness to the control panel and unscrewed the grounding wire. Open the lid and the switch pulls right out. The new switch drops right in. Attach the wire harness and grounding wire. Place the control panel back side first at an angle making sure the back metal panel is lined up, once in place it should snap back in place when pressed down firmly. You might have to reach in over the tub again and pull the clip down (keep Band-Aids on hand). Plug the unit back in and you are good to go. Raise and close the lid, you should here the switch click on and off.

Broken lid switch. The BIG problem was trying to figure out how to remove the control panel. There was no screws on the back top corners nor two screws at the bottom corners. The front end caps was not removal either. Finally I found on the internet that if you slide a putty knife under front corner of the control panel you can push back the spring clip on each that will allow the panel to be removed and lifted up. From there the lid switch is located on the left side and is easy to replace from this point forward. You can read other instructions on details on replacing the lid switch.

I researched the troubleshooting on PartSelect.com and determined the clutch was going out on my direct drive Whirlpool washer. I ordered the part, found the instructional video that actually had my exact washer being worked on, I followed all of the steps of replacing the clutch and in a snap, my washer was spinning. I've worked in apartment maintenance for years and PartsSelect.com has always been my only resource for appliance parts and repairs. The prices are great (I've compared most parts websites and 8 times out of 10, partsselect.com is cheapest), the shipping is extremely fast and the parts are alway right. Great site!!!!

Follow the video to remove the cabinet. Did NOT have to lay the unit on its back in order to replace all 5 springs. These may be easily replaced with the washer standing upright. The back Suspension Spring was removed by using the access hole in the back of the washer to remove the screw holding the back spring bracket in place. Reassembled the cabinet per the video. Except for moving the washer around, this was an extremely easy repair. To facilitate moving the washer - use Moving PADS placed under the 4 feet of the washer.

Disconnected electrical and then water inputs on the rear of the cabinet. Tipped the machine onto its front. Found that a spring was unhooked and dangling from a bracket. I searched for the location to secure the spring and found a hole on the rear base of the cabinet rusted through. I drilled another mounting hole nearby, Since the original spring had also broke, I replaced it with a new one from PartSelect, securing it between its bracket and the new retaining hole. Returned the machine to its upright position, reconnected water input lines, then its electrical. The machine works fine once again.

Unplugged washer, took out screws that held on the dial panel, lifted dial panel, disconnected the ground wire, released the clip, lifted the lid which released the switch. Installed new switch closed the lid which holds it in place set the clip connected ground wire reattached dial panel secured it with the screws, plugged the washer back in and I was on my way the conquer that pile of laundry that had built up.

I watched a Part Select video on replacing the augitator and just followed the directions to replace the thrust washer (which was showing wear) and the washer. The instructions that came with the thrust washer were helpful as well.

First, I moved the washer with water in it from the wall. Then, I removed two screws with a phillip head screwdriver from the back cover to the controls. Then I used a little bitty wrench to remove two small bolts that also held the back cover of the controls to the rest of the washer. The control panel was all attached, so it had to lay forward on the washer to remove the broken lid switch and then to install the new lid switch. There was one screw that I removed with a phillip head screwdriver. I removed the broken part and placed the new part into the hole. Then I had to move the control panel with limited space to lift the lid of the washer; the part would not fit property without lifting the lid. Once it fit into place, I closed the lid and replaced the screws and bolts. It worked beautifully. Thank you for your online help and the remarks from other people who had previously fix this lid switch.

Leaned the washer back to get at the bottom, removed the water holes, removed the water pump, removed the motor, replaced the direct drive motor coupling. Put it back together and it's all good. No clutch or drive problems. Simple fix.

I generally followed the video. Disconnected the water hoses, removed the front, laid the washer on its back. My water pump is rusted onto the motor shaft so I left it in place. I removed the water pipes from the pump then removed the pump/motor/gearbox as one unit. Watch out for more water than you think being released from the pipes and pump!! Everything works well with the new clutch fitted.

I replaced lid switch. Take off two screws off the back of insterment panel. Unscrew switch and unplug. Then reverse. Easy!!

When I pulled the machine out, I noticed one of the suspension springs on the floor. I followed the video supplied by PartSelect.com and suggestions by other folks. I started with the spring that was missing, which was a mistake since I did not know that there are custom spring clips which hold the spring to the drum. Once I found the missing part the installation was very easy. I used the suggestion by another post, of wedging a block of wood between the back of the machine and drum, to relax the rear suspension spring, which eliminated having to remove the back of the machine or tipping the machine on the back to get at the screw. I will always look to PartSelect.com for any future appliance repairs. You are the greatest