38EN-4CXW ((9X)) Maytag Range - Instructions

Turned off the power at the breaker box, cut the wires approximately 5 inches from the bad receptacle and removed it after removing one screw. Stripped back the wires about 1/2 inch and attached the new wires with the ceramic wire nuts provided and secured the receptacle back in place with the new screw provided in the kit.
My sister's husband wanted to scrap the whole range but I repaired it with $14.00 worth of parts.
The element is working great now.
Whenever I need appliance parts again I'll use partselect.com.

Removed and replaced above named parts, rewired.Be sure to tighten all nuts that secure wires. I believe this is what caused the problem.

It was so simple to repair - all I had to do was slide the older burners out and slide the new ones in - it took less than 10 min to complete the whole job! No tools used at all.

Unplug Stove removed screws pulled out
element. Lifted off the wires with a pliers they slid
onto the element ends that were pointed up
was very easy.

I received my ordered in less than a week. It was great. The day I got them I remove the old burners and replaced them with the new ones. It took me about 3 minutes total. I was then able to cook my Christmas dinner with out any problems.

Pulled the stove out, removed the sides and attatched the new springs( replaced both while the stove was out). Worked like new and put the stove back.

Replaced receptacle but it was not the problem. After further inspection I believe that the problem is the switch. The switch is on order now from Part Select.

Worst part of the job was removing the old screws that held the two old rectecles in place for the two burners I repaired. Once the screws were removed cut the wires stripped them and used the porceliean wire nuts provided with the kit. Easy job and good instructions.

Removed the screws that held the element and disconnected it. Placed the new element in the proper place, connected the wiring, and replaced all the screws. The unit worked beautifully, and all is well. My wife is happy.

Removed 7 screws on sides and one on top of stove. Replaced both springs (only one was broken but did both). Took around 15 to 30 minutes from start to finish.Fastest shipping in history during holidays without paying anything extra.

Had a technician from Home Advisor to check the problem out with my Whirlpool Double oven(1 1/2 old). Paid $60 to find the problem. According to the technician problem was control board and cost of labor and parts $465.00
Jumped on Part Select website, placed a question with my stove problem through the chat. Immediately they answered my question and told me the problem was the Terminal Block. Cost of part and shipping $25.00. Replaced it myself and everything works fine.
Thank you, Thank you Part Select for your help and honesty.

Sincerely
Peter from Maryland

This is the second time PartSelect came through for me. If it hadn't been for you guys, I'd have had to buy a new Jenn-Air cooktop, because ours is nearly 30 years old. About two years ago, I bought a new two-burner cartridge, which installed without tools in about one minute. But a few weeks ago, we lost the burner in the other cartridge. I emailed PartSelect, and even though I gave them my obsolete model number, a helpful service rep managed to find me the part number of the correct burner, so I was able to place my order. Once the part arrived, there was no problem replacing the burner. This is a simple operation we've performed many times when we need to remove the burner for cleaning.

Plugged in the new burner, which we received in one day.We were delighted with the quick service

Remove burners using my hands and replace new burners using my hands.

In principle it should be easy to replace the broil element in the wall oven, after unscrewing the supports for the back and front of the element (see other postings for details). The difficulty is with the ground screw, which is inconveniently only accessible from behind close to the back wall of the oven. A very short phillips screw driver is required, but designed so that good torque can be applied for unscrewing and replacing. The newly designed ground connector on the latest replacement elements makes life a little easier, but still be prepared to work slowly and carefully to complete the replacement. Note the new ground screws supplied only work with a flat-blade screw driver, not a phillips-type.