36272205891 Kenmore Range - Instructions

Check the switch with an ohm meter, 0 resistance in the closed position = a bad switch. I went to the web site found the part. ordered it next day it shows up. Removed the pot grids and all control knobs for the burners and oven lifted the top of the stove up, and off. I removed face plate behind the control knobs 3 screws, I removed the 2 screws holding the oven switch. opened the oven and un cliped the thermostat wire from the back wall. Uncoiled new wire feed under the burner shield to the back of the unit and back down the old hole cliped in the new wire. put the 2 screws into the new switch and re-assembled the rest in the reverse order i took it off . all this while watching my 11 month old grandaughter.

Really simple..Opened the top of the oven and followed the four wires hooked to the igniters on the burners to the back of the oven. Unscrewed top section in back of oven. Found spark module screwed to uppper back of oven on right side. Used a nutdriver to take a few screws out of upper back of oven. Unscrewed spark module from oven. There are six wires - four to the burners and two to the power supply....Wires are attached by connectors so didn't have to do anything but pull the connectors off the old spark module one at a time and push them onto the new spark module matching postion of each wire. Screwed spark module back onto back of oven. Screwed back section of oven back onto rear of oven, and that was it. Works perfectly. Saved more than $100 for service call and whatever elevated price they'd charge me for the spark module.

Checked switch using test meter and found voltage going in but no voltage out when switch was turned on. Removed all burner knobs, raised top cover and disconnected two wires from thermostat switch. Removed the thermostat probe from oven interior by pushing it through hole in top. Removed two screws holding switch and pulled out entire assembly. Used a wire coat hanger pushed through hole for probe so I could see where to fish the probe into the oven. Hooked up electrical connections and tested. Everything worked well.
Received part from Partselect in one business day. Excellent service and response.

The repair was fairly easy, you take off all the burner knobs there are small screws on the face of the cover panel and a few on the bottom That come off the cover panel should come off after you remove the screws and the switch for the oven light the wires just clip on the switch there are two .the thermostat is held on by two small screws that are on the cover panel.you lift up the burner panel you have room to feed the thermostat wire in the stove,there is a small hole in the back were you feed the wire through then the metal part is held in place by two small clips that are in the oven on the back wall.I didnt have to trouble shoot becase I knew what part I needed because it was broken,It was a fairly easy repair hopefully this is helpful

Good Luck

Take the advice that it's the igniter. Even thought the igniter lights, it doesn't mean it passes the correct current to the valve. Too much or too little won't work. I'd suggest changing the igniter first. I used to be in the valve business, that kind of valve lasts millions of cycles. The igniters on the other hand break down after a5-10 years

I had to open the top of the gas range and remove the front panel where the knobs are. I was able to identify where the thermostat wire went.
I had a little trouble figuring out how to thread the thermostat wire into the back of the range but then I poked the old thermostat through the hole from the inside so I could tell where it went.
I just had to put all the screw back in and check it and it worked fine.

I had to pull the drawer to get to the burner, then remove the heat shield to get to the connections. I took out the screw at the end of the burner tube, then the two screws holding the tube to the back wall. I had to pull the connections through the back wall of the oven, and disconnect them. I then removed the two screws holding the igniter to the old tube, and used them to connect the new igniter to the new tube. At that time, I also had to cut the old connections off of the old ignighter, and put them on the new one. I also had to redo the connection to the gas valve at the bottom of the tube. I then put all the wire and connections back through the hole in the back of the oven, connect the tube back to the rear of the oven, and the single screw to hold the end of the tube. I replaced the the heat shield, and tested. Everything worked fine.

remove two screw lift top slide glass in place install top done deal

I found the best was to remove the oven door and the broiller drawer. Then I removed the panel that seperates the two areas. This gave me great access. Next I removed the shield (1 screw) and the burner (3 screws). Then the inlet pipe (don't forget to turn off the gas, as I did). Remove the valve (2 screws)...........Remove the mounting bracket from old valve and install it on the new one. Then it's just a matter of reversing the prior steps and your'e done!

removed two screws with screw driver,and replaced panel

My Hotpoint gas oven became extremely hot after using it . Only after unplugging the electrical cord, turned it off. Replacing the control valve (thermostat) solved the problem. The stove top had to be pried up with a flat screw driver then propped up. Prying off the oven control valve revealed two mounting screws (philips head). Next remove thermostat sensor bulb inside oven at back wall. Remove old thermostat control and bulb assembly. Installation is reverse order of disassembly.

While i was inserting the new lp,gas orriface to the right rear burner tube I dropped the oriface.Without looking i popped the top of the burner unit, like most older type stoves, and thats when i ran into my problem. I realized the burner tube assemblies are attached by 3 screws to the top cover.Not attached to the cabinet as the older models, Basically cracked both front aluminum tubes trying to retrieve the dropped oriface. so i had to replace the burner tube units, which involved removing 3 screws, and loosing up and removal of the nut to the main gas tube. extremely easy repair, next time i`ll try to remember look before i leap,total time to (r+r)burner tubes about 20 minutes.Parts select pulled me out of the fire on this one, great staff and service, with quick delivery.

I was very pleased with how quickly the new oven rack arrived and it was a perfect fit. Thanks.

Here's how I fixed my problem.
I took the aluminum cover, the part that sits over the jet & the igniter, which simply comes off. It's the part that the igniter discharges to. I took this cover off & using a pencil I scratched the lead of the pencil into the area
which is around the igniter. I made sure to cover the area with as much lead as I could get on it. You need to make sure that you do this to all four burners. The only care you need to take, is not to block the gas jet which is in the igniter recess. It's been about 3 weeks since I added this & the burners click loudly & have lit without a problem. It appears that the aluminum may develop a coating on it of some kind which is highly resistive.

my husband who is very handy took it a part, replaced the glass and put it back together - he did remove the door from the oven first and put it on the counter to work on it.
I had the schematic picture of the door ready in case he needed it. He didn't really.