35F Maytag Range - Instructions

Liza from College Point, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

69 of 132 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Rented appartment in which none of the drain pans were the proper size making it very difficult to cook

I removed the element and then the drain pan and replaced with the new correct pans. I replaced the element and all was well.

Parts Used:

Grace Mary from Canton, OH
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

65 of 129 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Broiler unit would only heat on one side

Removed the screws that held the element and disconnected it. Placed the new element in the proper place, connected the wiring, and replaced all the screws. The unit worked beautifully, and all is well. My wife is happy.

Parts Used:

Lawrence from Morganton, NC
Difficulty Level:
Really Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers

8 of 9 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Replacement of broil element in wall oven

In principle it should be easy to replace the broil element in the wall oven, after unscrewing the supports for the back and front of the element (see other postings for details). The difficulty is with the ground screw, which is inconveniently only accessible from behind close to the back wall of the oven. A very short phillips screw driver is required, but designed so that good torque can be applied for unscrewing and replacing. The newly designed ground connector on the latest replacement elements makes life a little easier, but still be prepared to work slowly and carefully to complete the replacement. Note the new ground screws supplied only work with a flat-blade screw driver, not a phillips-type.

Parts Used:

David from San Rafael, CA
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers

4 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

The Broiler element split after oven self-cleaning

We at first thought the replacement could be done by just removing 2 screws.
When in fact it was necessary to pull the oven from the cabinet, remove the rear metal shield in order to unplug the element.
The job went rather smoothly at a considerably less cost than if I had contacted a repair service which would have upped the price of the element plus the cost for the service call.

Parts Used:

Rolland from New Port Richey, FL
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

needed to replace stove pans and burner

An easy replacement job.

Service from you was prompt and the replacement parts arrived in perfect condition...thanks

Parts Used:

Economy Y-frame Surface Unit - 6"

Marylou from Sitka, AL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

3 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Replaced Broiler Element

Turned off oven power.Removed oven heat shield, element support clips and element mounting plate screws. Disconnected three element power wires and ground wire. Removed old element. Reversed removal procedure for new element install. Piece of cake.

Parts Used:

Phillip from Reston, VA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

burner would not heat.

I unpluged the old burner and pluged the new one in. Repair done in about 2 min,

Parts Used:

Economy Y-frame Surface Unit - 8"

Jackie from Hughes Springs, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

replace element

remove two bracket screws, and remove bracket, the remove two mount screws for element. then remove the element. installed the element in reverse order that it was removed.

Parts Used:

alex from huntington, NY
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

replacing old drip bowls

It was so simple & the parts fit perfectly. I appreciated all the help from your sales lady. Thanks again.

Parts Used:

Marion J. from Palmetto, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Burnt out

All went well except for error on instruction sheet.
Ground wire used on earlier Models attached to the ground lug is no longer used?? and should be removed!!! Guess what the ground wire has to be used or the element will not heat up.Soooo someone at the mfg. has no ideal what they are talking about,You have to ground the element or it will not come on.

Parts Used:

David from Elba, AL
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Element burned out, broke circle, heat only half

Repair went fine, insert helped, just take your time and remember the way you took out. Started without takeing door off, I am to short and door comes off easy, unscrew the two screws holding element leaving one not quite off then the back two screws then go back to upper screw remove and element will pull out, remove 3 wires remembering the order, Wiring is a little tricky (in the stove-just 3 plugins), just pay attention and will go smooth. Then remove element and go backwards and presto your done.

Parts Used:

Michael from Thornton, TX
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

ELECTRIC BURNER SUPPORT FELL OFF AND BURNER SOMETIMES WOULD NOT COME ON.

Stuck the new one into the plugin.

Parts Used:

Economy Y-frame Surface Unit - 8"

RICHARD from SHOW LOW, AZ
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Drip Pans were stained and burned on.

Replaced drip pan. Notch did not want to match the burner notch. Was a close fit bit with a little pressure made it work.

Parts Used: