30TESKWED-23-03 Tappan Range - Instructions

First thing I did was to turn off the range supply breaker. There were two screws, one on each side, that held the lower element into place. I used a phillips head screw driver to remove the screws and pulled the element out for access to the wires. I pulled the connectors off of the element and remove it from the oven. I them put the new element into place, attached the wires, replaced the screws and turned on the breaker. It was an easy fix.

Turned power off at electrical panel. Pulled oven away from wall. Removed back cover (6 screws), then unplugged wires from old receptacle. I had to pull the squeeze clips backwards & break them to remove the old receptacle - couldn't squeeze them enough to remove them otherwise. The old receptacle came out through the inside of the oven, and the new one snapped in easily from inside the oven as well. Replaced wiring, installed new bulb, restored power & tested. Replaced back cover. Good time to vacuum under/behind where the oven usually lives before sliding it back to the wall.

Most of the job is simple fastener mechanics.
Use a nut driver or Phillips screwdriver. Remove rear panel.

Pull out control knob. If it is stuck, wrap a small rag around the back of it and pull the rag steadily.

Carefully match marked terminals on the replacement switch with those on original. Switch terminals may not be in the same location. Replace wires one for one, one at a time.

Carefully select the correct knob filler for the switch post. Several are supplied. Proceed with logic and measure the shaft length and the filler length and type to match.

I removed the two element screws, one on each side. This was very easy and fast.
I then pulled the old element towards me about
three inches to expose the wires attached to each
end. The wires have a slide on terminal connector
so replacement is easy, but you must hold the
terminal connected to the wire then pull the element off. Do not try to pull off the element by pulling on the wire you can cause damage to the
wire and create a new problem. Once the old element was removed I attached the wires to the new element by sliding the terminal connectors on each end and pushed them firmly into place. I then pushed the new element back and replaced the screws on each side and the repair was complete.The repair took all of about 5 min. The best part was I received the the new element from Parts Express the next day and had the oven working within 24 hrs.. The repair service could not do it that fast. Do it yourself, you can save a lot of money!!

Snapped the new part into the slot the old one had been in.The repair including opening and closing the drawer took less than a minute.

First I unplugged the the stove. I then unscrewed the two screw holding the element. Because I had read the other repair reports on the site, I was very careful in pulling the element out so I wouldn't lose the wires in the rear of the stove.
Once out, I held them with the pliers and gently pulled the element until it was loose. Plugged in the new element screwed it back in and plugged in the oven. Worked like a charm. By the way the part arrived the day after ordering it!!!! This is a great site.

Your online instructions said to remove the two screws and pull out the heating element about 3 inches and disconnect. When I did this the element came out but not where it was connect to the wire., I could not locate the wire from the front of the oven. I then pulled out the oven from the built in cabinet and removed the rear panel. Then inserted the element with the 2 screws from the front and connect the wires to the element from the back of the oven. Jim

Remove old element by removing two screws on back wall of oven, pull attached wires out about 6" and disconnect. Reverse to install, very easy. Of course the oven door makes it harder to get at things, but it all worked out. Partselect was the only place I could find the element since the stove is 18 years old. I love keeping appliances going as long as possible.

The repair was straight forward and the video was a big help. I removed the oven racks and then used a 1/4" socket with a nut driver to unscrew the bolts at the back. Since this is a really old oven, the connecting wires were a bit difficult to remove from the bake element connectors. They seems kind of stuck, so I took a small, thin screw driver and pried up one of the metal clamps of the connecting wire just enough to let me budge the connector to detach the bake element. Had to do that for both sides. Then I just put the new bake element in, attached the wire connectors, made sure the wires and the ends of the bake element were all the way back in their holes, screwed the screws back in, and then put the racks back in. It was really easy, except for the bit of a challenge getting the wire connectors detached from the old bake element connectors. Works now without catching fire. :-D

First of all I removed the top panel then removed the switch. I then took pictures of the switch & drew a sketch with all the info. Then I went to your web site, matched up the switch & ordered.
When the switch arrived I went thru the above replacing the bad switch.

From learning the hard way on a previous repair, I opened the circuit breaker for the oven at the circuit box (arc welders use 220 volts also). Then using a nut driver, I removed the two retaining screws and pulled the bake element from the oven (about 3"). Then I removed the spade connectors on both ends of the element and reconnected them to the new element. Then I gently pushed the element back into the rear wall of the oven and replaced the retaining screws. This procedure is extreamly easy and very straight forward, anyone could accomplish this task.

order pcs fit perfect.

I removed the screws holding the element in place, pulled the element out, and one of the leads came off and dropped into the oven. I had to take the back of the stove off and feed the lead back through the hole into the oven. If I had been careful to keep the leads from dropping out of the hole, the whole repair would have taken only a few minutes. But even so, it was quite easy.

REMEMBER TO UNPLUG YOUR APPLIANCE FIRST!

shut off power to stove. Opened the oven door, removed the racks. removed 2 screws holding the element in place. gently pulled element out to expose connections. removed connections. discard old element. reattach connections to new element and reinstall. very simple.

First I unplugged the stove, and removed the upper-back panel. Then I pulled off the control knob. Then I removed the two screws holding the switch to the stove. Then one-by-one I removed the wires from the old switch and connected them to the corresponding tabs on the new switch. Then, using the knob adapter supplied with the new switch, I figured out how much of the knob shaft I had to remove from the new switch to position the knob the correct distance from the face of the stove. Then I tested the switch with a voltmeter as instructed, and then I hooked up the last wire.
Partselect.com is an awsome website!!! I was able to review comments form other do-it-yourselfers that had similar problems. Then I looked up the Partselect schematic drawings of my stove and was easily able to find and order the part I needed. The part arrived at my house within a couple of days and I had the stove fixed in no time.