30TESKWED-04-23 Tappan Range - Instructions

Watched the video

Turned off power to stove;removed baking racks , loosened Holden screws to pushon bake element removed old bake element,installed new pushon bake element.

Originally I had anticipated a major problem requiring the removal of the back of the range and perhaps the necessity of employing the services of a repairman ($$!). Fortunately I waited for the arrival of the replacement element, which, upon inspection, was not configured to go through to the back of the range. What a relief!

The hardest part of the repair was finding the correct nutdriver (5/16"). Removal of the damaged element was simply backing out the two retaining screws inside the oven and pulling the element out far enough to expose the clips to the wire. Pulling them apart was easy enough, and then the element I disposed of immediately.

Reverse of removal of the old element was the installation of the new: Reconnect the clips to the element, push the wires back into the insulation, re-inserting the two retaining screws and tightening them gently.

The final step was to plug the range 220 cord into the outlet. Testing whether the element was functional was a breeze; the oven and the range elements worked perfectly.

First we turned off the electic, then we took the back off the stove and pulled the wire off the bad element then replace the new element. It was very easy to do.

Unplugged the stove first !
Removed bake element ; (2 screws), looked OK,
measured with an Ohm meter, measured "open".
Also, removed rear cover (6-screws), wires not burnt. Ordered new element-rec'd next day! My wife installed it and replaced rear cover. Works great (oven!) and about $10 cheaper and quicker than from a local dealer!

I unplugged the damaged element and plugged in the new one. It took less trhan 30 seconds and the unit worked just fine.

Very simple. Removed oven rack that had melted residue on it and replaced it with the new one from your company. I want to tell you that the delivery service I received was just geat. Took less than 48 hours to arrive at my home from the time I placed the order on line. Keep up the good work and I will be happy to share my experience with those in need of you services. Thanks. Marilyn Kasson

It's a simple project. Remove old element and replace it with new one. Access is easy. Only one tool needed. What impressed me was how fast the part got here, like the next day after I ordered it.

The repair was very simple and easy. All I hqad to do was remove the old knobs and attach the new ones. No tool was required.

Sat on floor, pulled drawer out, inserted new clips, remounted door, stood up, high-fives myself.

Simply...2 hex head screws removed. Unplug old element...plug in new element...place 2 screws back into place...test

Remove 2 screws. Pull element out. Slide 2 wires off. Just do in reverse it's done.

The broil element and range were both working so I removed the bake element to test for continuity. Use a 1/4” socket or wrench to remove the two screws holding the bake element to the rear wall of the inside of the oven. Pull the ends of the element out of their recesses taking care not to lose a wire inside the back panel of the oven. Pull the wires off the element ends. You should be able to do this by hand; use a flathead screwdriver for a little prying if necessary. Visually inspect the element for physical damage. If you don’t see any, test the element with an ohmmeter or multimeter. If it reads anything other than 0 ohms (continuity), your element is defective. Installation process is reverse of removal.

Using a socket set and Robertson #3 (smallest) driver head,with the breaker shut off before working I removed the old element and disconnected the old element from the wire connections.I then installed the new element by connecting the terminals to the wire connection in the range before screwing the old retaining clips to the back of the oven compartment wall.Then I flipped the breaker switch back on and turned on the oven dial to 425 degrees to see the element heat up and glow red affirming the success of the repair.Total time to repair about 15 minutes.

Pulled out the old, and replaced. Very simple for a 62 year old woman! I cook a lot, being from the country, and Imwas so excited to get my burners fixed! Should have done it years ago! Thanks!