30-2632-02 ((03)) Frigidaire Range - Instructions

1) Turn off the gas and disconnect the power

2) Remove oven door. There requires that you remove the two square drive (SD) bolts on the inside, partially close the door and lift it off the hinges.

3) Remove the grills.

4) At the back remove the rear shield (aluminum panel held by 2 SD sheet metal screws.

5) this exposes the broiler igniter and its two wires. If its been replaced in past, there should be two porcelain screw-on wire connectors. Undo the connectors by turning them counter-clockwise. With a volt-ohmmeter, measure the resistance across the igniter. If its open circuited, its broken. If not, then its in the circuit board, and this help stop here. If this is the original igniter, it ends in a plastic connector. Disconnect by pulling it apart from its mating plug and again, check the continuity of the igniter. If its defective, reconnect the connector and cut each wire on the igniter side. Strip back about 1/2 inch of insulation on each lead.

6) inside the oven, using the SD driver, remove the 4 screw securing the broiler burner from the roof of the oven. The burner can now be removed, pulling the burner away from the gas jet on the right.

7) The igniter is now exposed and can be remove by removing the two SD drive screws.

8) Replace with the new igniter, being careful not to touch the black element, and feeding the wires though the rear oven wall.

9)Reverse the above dissembly procedure.

10) Broil the sausages.

Took out the old & easily replace it with the new set. No tools required.

Just to point out the pans were delivered within a few days which was very quick. I just dropped them in. They fit perfect. Thank You for no stress.

I threw the old ones out and replaced them with the new ones. It was a no-brainer :) The parts arrived super fast. Great, no hassle service.

No installation steps required. I did have very fast delivery of parts ordered.

take broiler oven door off. replaced the wire clip on one side of the two wire harness. on the other side, I clipped the other wire, used the wire sripper too strip each side of the wires and used the ceramic wire nut that came with the kit. I did not have to remove any part of the stove for this job. twisted the wire nut on, and my job was done ! replaced the broiler door and you finally are able to cook your famous meat loaf ! Mike

remove screw, remove burner, install new burner and screw

No Problem, couldn't find them at any local repair facility so I looked on line and found them here, ordered 4 drip pans and the exact replacements came within a few days.

My existing igniter glowed but the oven still did not light. I determined it was too weak to activate the gas valve so I replaced it. Simple fix, four screws, wire nutted the two leads. Fired right up, took about 30 minutes to replace.

I found your website fast and easy. I needed replacement drip pans fast, ordered them on-line, and received them within 3 days of ordering. Your parts were the best deal, the least shipping charges, and the picture and description on your website was the best. Thanks.

As the previous people stated on similar repairs;
I took the new drip pans out of the box,removed the old grate burners and the old rusty drip pans; then, simply set the new pans in place and replaced the existing grates. This whole process took less than 10 minutes.

Opened the box, took out the drip pans and the put them on the stove. Wow -- even a techno-challenged person like myself could do this! I ordered these on a Tues. at 2:00 p.m. and received them on Wednesday -- that is a first so thanks for the fast service and they look great! Was non-existent to find them at local appliance stores in the area so thank you for having them.

No major hardware stores had anything close. One visit to you site was all it took. Parts were loose so we removed them and replaced.

Found replacement drip pans at partselect.com.
Ordered them and received them in 2 days.
installed the new ones and all is well.
Had I known it was this easy, I wouldn't have spent countless hours scrubbing the old pans with Brillo pads. Considering how much I spent on oven cleaner, scouring powder and steel wools pads, it was lest costly to just buy new ones. (and they look better too).
Thank you PartSelect.

Opened box, popped bubble wrap :) put in drip pans. Was great! Having been looking for the correct ones for a couple of years!