2DLXR7244MQ2 Whirlpool Washer - Instructions

Unplugged power cord and disconnected water lines; note which is hot/cold. Washer was then tipped on its front. Discharge hose was disconnected. Washer was then rolled over onto its back as this would put the pump on top for much easier removal.

Pried off two clips attaching pump on motor using a flathead screwdriver. The rear clip was done by touch. Unplugged wiring plug from motor. Using an adjustable wrench (socket set would have worked better), remove two screws holding 2nd set of clips attaching motor on transmission. Then pried off clips.

Removed old coupling from transmission shaft and motor shaft, plus middle 6 hole widget thingy.

Installed new parts on transmission shaft and motor shaft with fingers pointing towards each other. Using a small hammer, tapped the parts onto each shaft. Placed 6 hole widget thingy on the transmission part, and then rotated motor so motor part would fit in remaining three holes.

Replaced clips to hold motor on transmission and reinstalled screws holding clips.

IMPORTANT: Replace motor wire now. I forgot to do this and after the tub was filled with water, realized that, and since the pump was also disconnected, could not get the water out. Had to get wife to hold washer up while I crawled underneath to reattach motor wire. Learn from my mistake!

Attach pump onto motor and replace clips. Double check everything is back in place.

Roll washer onto front side. Attach discharge hose. Tip washer back upright. Reconnect water. Reposition discharge hose and plug washer into power.

First try it smelled like something plastic was burning, but I think that was the old part shavings getting ground away.

Remove the main bolts that hold the gearbox in place, pull the gearbox and shaft out. You will see the brake shoes and drum--the large spring is a struggle to replace. Getting it out was not hard. The biggest struggle I had was replacing the brake shoe spring after replacing the shoes. I ultimately compressed the spring in a vise, then used safety wired it, then placed it between the shoes, then cut the wire to relaease the spring.

I basically dismantled the washer and turned the washer over to access the motor,transmission and pump.I disconnected the electrical connections first.I then released the clips for the pump and the clips for the transmission.The coupler was broken in little pieces.I went to Google to search for parts and happened to reach your Web Site.I found the part number for the coupler from the schematic and ordered it.It was then I discovered the part number for the cam dogs for the agitator so I ordered it also.While on you site I read the various troubleshooting stories and how each was repaired.I put myself through a lot of unnecessary work by dismantling the whole washer when all I had to do was turn it over and access it from the bottom.The parts arrived in three days and the install was rather simple thanks to the direction of your site.I had a heck of a time reassembling the washer but all in all $42.00 was a lot cheaper than a repairman or a new washer.We now have a working washer and no leaks.
Thanks to your site ,I have a happy wife and clean clothes.

1) Unplugged electrical cord
2) Removed hot/cold water hoses
3) Took drain hose from laundry room recepatcle
4) Moved washing machine to area where I could lay it down on its back (very important for easy fix)
5) Found (easy accessible in my case) water pump with an inlet and outlet water hose held on with spring clamps.
6) Removed each of the two clamps with pliers and each hose by twisting loose
7) Remove two metal clips holding pump to motor housing
8) Slide pump off shaft - removal is finished!
9) Reversed process for installation, making sure to gently align pump housing when the pump is aligned with the shaft
[probably took less than 15 minutes]

before ordering the parts, I pulled the cap of the agitator, removed some internal parts of the agitator - had to remove one hex head bolt, and noticed the threads on the 3 little teenie weenie plastic dogs were worn off. I bought the repair kit on line after entering the model number, parts were here in a few days, and the repair took about 15 minutes. Works like new again.

The directions provided with the parts were very clear and made the job quick, easy, and painless.

I ordered the parts at a minimal cost compared to the repairman's quote, they arrived in 3 days. I used the laptop and put it right next to where I was working so that I could follow the directions step-by-step. The instructions were easy to follow and showed you right what to do so I never had any questions. My washer had a slightly different configuration but I figured it out. Replacing the parts was simple, take one off, put the other on. Putting the washer front back on was a little tricky, I had to have my daughter help me hold it in place while I wiggled it around to make sure it was just right before I screwed it back together. It was easier than I thought it would be. I told my husband I loved the internet, I would never have been able to do this job without the instructional video. Thanks PartsSelect!

Turned off water and pulled power plug, Then unscrewed hot and cold hoses from washer.
I took off the top control by undoing the 2 screws in front and then the two screws on the back plastic latches. Mover it forware and took off the 2 screws on the bottom of the back which came up and off easily. Undid the two screws holding the Water valve to the back and undid the water outlet tube and the wireing. Replaced with new valve and reattached tubing and wires. Screwed back on and reattached controls.
Actually was very easy even without repair manual to the washing machine.

First I removed the screw that held it in place with a socket. The agitator became loose and easy to remove at this time so I lifted it from the washing machine. I then just placed the new agitator in place and replaced the screw being careful not to do it too tight. The replacing of this part was an easy job and thanks to Part Select it saves me hundreds of dollars.

I had a little difficulty at first, trying to remove the back of the unit. I then figured out that the repair was to be made by leaning the washer back and removing it from underneath. That became really easy as the bottom is open.I had to remove one nut and then the agitator from inside, then tilt the machine back, disconnect the two hoses from the pump, remove three bolts and lower the motor/ transmission assembly. Then I had to disconnect the motor from the pump ( with two snap on clips) and remove the broken plastic coupling. The new coupling had a metal insert that seems to make it stronger than the original piece.I then just reversed the procedure to put it together again and it worked fine. The part was shipped immediately and I got it sooner than I expected so I greatly appreciate that. Overall it went well, and by the way, it was my daughters washer and she was happy as well.Thanks, Roger

First, I'm so excited that this site exists because I knew that the problem was minor and I didn't want to pay the outrageous housecall price of a repairman. I read other customers' experiences on how they fixed the problem and that made it sooo easy! Basically unscrewed the screws on the far left and right on the top panel, folded it down toward front, unscrewed and unplugged the ground wire and replaced the part. Someone else had warned that the lid should be open to remove it and that was a huge time-saver. Thanks so much! The part was broken because of very poor design. The part actually worked fine, but the piece of thin plastic that held the part in place broke. Back to the drawing board Whirlpool.

Read the directions in the repair kit first- a 7/16" socket and 10" extension is needed. Assembled new dogs on agitator "cup" and retainer, added marine(waterproof) grease to assembly washer, replaced bolt anyway and installed new o ring. Took less than 15 minutes-READ ALL DIRECTIONS FIRST!

I thought the click of the lid switch sounded different so I pulled the top console and tested it for continuity in both positions and found none. When I by-passed the switch the washer started up, so I knew what the problem was. There are four screws involved to remove the console which reveals the lid switch to the left side. There's a single screw for a ground wire but the switch itself is simply snapped in place after disconnecting the wire harness plug (must be done with the lid open btw).

I was lucky to diagnose the problem accurately so that the first thing I suspected turned out to be the problem!

First off unplug the machine then turned off H/C water supply and removed hoses, laid the machine on its side, removed 3 motor supp. bolts, loosened drum pulled out shaft and clutch assembly was right there. Also replaced coupling while it was apart. And to think, a svce company wanted 179.00 just to walk in my door and diagnose the pblm. Then, parts and labor were extra. Thanks for the help/advice, piece of cake!!!!!!!

I unsnapped the top of the mechanism and removed the agitor assembly, (I had already put together the new one,) I just had to unsrew the old one to get it out and screw in the new one. This took me less than 10 minutes from start to finish. My husband was away for the week and this was left up to me if I wanted it done. So I (a female) decided that I would attempt it.
A Piece of Cake. thanks to Parts Select, I have a few more years with this machine. I was really hating to purchase a new machine. So for less than $25.00 with no service call "I Fixed It!"

Removed top cap on agitator w/ flathead screwdriver. Removed protective cap over bolt and cog housing shaft. Used 7/16 deep socket w/ extension to remove bolt. Removed housing where stripped cogs were located. Cogs seated loosely in shaft housing no tools required to remove cogs. Replaced cogs in housing, made sure everything was lined correctly. re-inserted housing into shaft. ,screwed bolt, replaced caps and works like new.