24FA-6CKXW Magic Chef - Instructions

it was really simple with the kit and instructions that came with the kit everything i needed was in the kit, and hats off to you guys

First let me say that I tried several places to get what I thought was a simple light bulb. This included several national hardware stores as well as a national electrical supply company. No luck. Went to the manual and PartSelect. Not only did you have it in stock, ship right away,at a reasonable price it arrived in a matter of days. One would not normally think of receiving a "how to" video to change a light bulb but you did. That impressed me. Suffice to say the replacement went well and you can be certain the next time I need a part I will go to you first. I am also impressed with the organizations with which you are affiliated with. BBB, Norton, PayPal, money back guarantee etc. Thank You The entire process was made pleasant with your support.

followed video took 10 minutes, almost went anf bought a new stove

The only difficulty with following the supplied video, is that my ignitor did not come out as easily as a few turns of the screwdriver. The screws stripped as I tried to remove them, making them twirl in their holes. I had to apply back pressure for them to come off and free the ignitor for replacement. Other than that, the installation went smoothly, and the oven sprang to life within 10 seconds of turning it on.

I simply followed the "general" instructions from the online video "Partselect" provides and perused the instructions included in the kit. The OEM igniter was much longer than the replacement but the new part was spec'd just fine. It was necessary for me to open up the back of the stove in order to retrofit the igniter leads to the original block connector and install the heat resistant padding included in the kit. The additional necessary hardware fit very nicely inside the oven. The stove's oven fired up without any problems and spared me the expense of purchasing a new oven. Thank you very much "Partselect".

I removed and replaced the igniter. I described these symptoms on the web site and it detailed that90% of the time by installing a new igniter it will fix the described problem. So I ordered the part and installed the part and everything worked OK. The only tool I had to use was a screw driver to remove three screws. It took about half an hour. If I had to do it again it would take about 15 minutes.

Unplugged oven. Removed door,racks,and bottom shelf. Removed screws from ignitor and unplugged it from connection. Installed new ignitor with screws and plugged in to connection. Tucked wires behind insulation as they were before. Installed previously mentioned items and turned on to check. Worked great and am very pleased with PartSelect and the assistance they offer.

Slid oven out from counters. On each side there are 3 screws on the front and three screws on the back holding the side piece on. Once off, the spring was very easy to get at and replace. I had only one broken, but replaced both anyways. I think it took longer to clean the sides of the oven that haven't been touched in years than to replace the springs. This job was very simple and easy.

I didn't do the repair -- my husband did, said it was easy, had no problems what so ever! The new bulbs give a lot more light to the cooking area.

Ordered oven Igniter kit PS1573892 which cost $73.00. Received the kit with instructions easy to follow to install. I was surprised how easy it was to repair, with the help of my wife we did the job in about 2 hours, the oven now works great. I really saved a bundle of money doing this myself, a local repair service wanted $114.00 for the same part and $200.00 labor to install and this is the gospel truth. I am 96 years old. RMA Bluefield, WV

Take off oven door, remove racks, lift out bottom plate of oven, remove deflector shield, unbolt old igniter gently fish out the wire and plug from the back of the oven. Unplug and replace with the new igniter. re-assemble oven.

Followed the directions on the video. Very easy to do.

Removed itand replaced using a smcrewdriver, part was exactly like oem