2380EGS Jenn-Air Cooktop - Instructions

It is so easy. Once I found the right size of filter from the website, I ordered it right away. It came in 3 days and I just need to take out the old one and insert the new one. No instruction is necessary. By the way, the price of the filter is one third of that from Jenn-air.

Ordered new cartridges

Removed the old adapter and replaced it with the bright and shiny new one that fit perfectly.

* Do not lose the supplied CERAMIC electric connecting nuts; they will not fry in the heat.

* Unplug the heating elements from the old receptacles, and remove any rings; unplug the cartridge by lifting up the back side and pulling gently toward the back of the stovetop.

* Unscrew the cartridge top from the cartridge base (about 12 screws) and the recepticals, and cut the old wire close to the old receptacle.

* If you have a spare magnetic thingy around, use it to hold the screws and not lose them.

* Screw in the new receptacles, route the newer wiring from the receptacles (use as much of the new wire as possible), back toward the wiring block on the cartridge plug.

* Recut the old wiring to accomodate the length of the new wiring, but leave at least 2-3" from the wiring block, if possible. Re-connect them using only the supplied CERAMIC electric nuts.

* The CERAMIC nuts allayed my fears about the effect of heat on a plastic nut; ceramic is designed for high-heat environments.

* Reverse the disassembly steps to reassemble and reinstall the cartridge.

Replaced the drip pans

Pulled out the old burner and plugged in the new!

Pulled old knobs off, pressed new ones on. Probably well under a minute for 6 knobs. Anyone with the IQ of a horseradish could have done it. But what was really great was the help and personality of the agent at the other end of the phone. Shipping was as promised, and the entire experience was delightful!

took old knobs off replaced in 3 minutes

removed motor, saw that stablizers were broke and went to a local parts supply shop called SUNDBERG and was given a price of about 49.00 for three stablizers. at that point i went to the internet and found PARTSELECT.COM were i found the same parts for a fraction of the price,17.00, i could not believe it! SUNDBERG customer service was horrible.PARTSELECT custormer service is great and was just over the internet,any how the repair is done no more loud noise and wife is happy again ,for awhile.thanks keep up the good work.i tell everybody about you guys.

The repairs were very simple we just disconnected one screw then removed the old one and replace with new one. The left side took a little longer, because of the 8 screws we needed to remove to take the back panel off. But once we had it taken off the replacement was a snap. Nothing to it.

Turned power to stove off. Removed two screws from cover - lifted cover up and pulled switch out and disconnected wires. Put new switch in and connected wires. Made sure that it was in correct position by placing knob on to make sure off position was correct - then placed plate in position and closed - put two screws back on plate and put new knob on. Turned power back on and turned knob and burner back in operation

Ordering and installing was easy. The hardest part was getting the exact match to 20 yr. old appliance knobs. First one I ordered had wrong shaft hole, but it matched perfectly in design. Decided to reorder and just replace all four with matching new-style knobs and the correct shaft hole. Yeah. Looks great and REALLY easy to install.

No brain surgery required. Removed electric burner, put in new drip pans. Voila! Good for many more years of service looking like new.

1. Remove the exhaust vent cover, located in the center of the top of the range. It just lifts off.
2. Swivel the clamp 90 degrees to release the filter.
3. Remove the filter and throw it away
4. Place new filter in place and lock in place by rotating the swivel clamp back 90 degress.
5. Replace the exhaust vent cover

First I disconnect the breaker. I removed the defected receptacle and cut the wires. I connected the new receptacle with parts with the new part. Turned the breaker back on and everthing worked fine.