22JN-7KLXV8 Magic Chef Microwave Oven Combo - Instructions

Watch the video, it's too easy and best of all, the part fixed the oven!

removed grill cover, removed bulb plate, unscrew bulb, screw new bulb in socket,put bulb cover back on and screw grill cover back on. no issues whatsoever.

Since I had never done anything like this, I watched your video twice. The oven door and racks came out easily. The wire connectors had burned, fusing the plastic parts. I cut them off and spent more time looking for a wire stripper than on the repair. The new igniter looked just like my 1993 oven part. Works great. Be SURE to unplug and turn off gas before starting!

Ordered the part from this site. It arrived In the time thy said it would. Removed old oven igniter and replaced with new one. Removal of screws and old igniter. Replaced with new igniter and put screws back nd it was working again

Called a repairman who came to the house to check the oven and stated it could be one of 3 things but he was not sure what it would be. Stated 2 of the parts would be $200 and the third would be a rebuilt part costing $400. At his suggestion we ordered a new oven. However, before it came in the old oven started working so we cancelled the order. When it would not light a few weeks later, we went to the Maytag website and was directed to PartSelect. We found the list of problems, located the part we needed and received it within 2 days. We watched the video on the PartSelect site on how to install it. We paid the repairman $80 for showing up and he had no idea what to repair. We paid $42.28 total to repair it ourselves. Thank you!! We would recommend your services to anyone before calling for professional help!!

I first looked online at a video on how to replace the igniter prior to recieving the part. The part arrived 2 days after I ordered it (Christmas Day) and was an exact replacement. Taking the oven apart was the most difficult issue since there was some grease missed in the last cleaning plus a couple very tight screws. The igniter unplugged easily and reinstalled without cutting/splicing any wires. Oven was back together and fired up within 20 minutes. Outstanding service and would highly recommend PartSelect.

DISCONNECT AC ELECTRICAL POWER TO RANGE AND TURN OFF GAS SUPPLY TO RANGE 1. Removed door (slide up and off hinges), no tools required. 2. Removed grate/s and burner cover to expose burner and igniter. 3. Used hex socket tool to remove two igniter bracket screws. 4. Carefully pull two woven glass insulated leads connected to igniter until connector is in reach. 5. Use care not to put unnecessary strain on leads and connector body. 5. Squeeze locking tongs of connector, and unplug igniter leads. 6. While holding female end of connector, insert new igniter electrical plug, making certain they latch together. 7. Carefully push excess leads / connector body into recessed area and wrap insulation supplied with igniter kit around glass woven leads of igniter, to re-insulate the cavity opening. 8. Position igniter on burner tube bracket and replace hex screw fasteners. 9. Plug in electrical power to range, turn on gas supply. Check oven for proper operation. If oven does not light, shut off gas supply, unplug electrical power and contact qualified service technician.

really easy thank you to your video

Replaced light bulb.

Make sure power to the oven is disconnected. Remove all shelves. Partially open the bottom door and yank it out so it is out of your way. The igniter is next to the back and upper wall of the oven inside the lower (broiler) compartment. The igniter is held by two screws which I opened using a 5/16 or 8mm nut driver. After removing the two screws, remove the back plate using a regular phillips screwdriver. Next, pull out the two igniter wires until the connector comes out. Pressing the side tabs disconnect the igniter from the connector. Connect the new igniter. If nesessary, replenish some of the insulation with new insulation that arrived with the new igniter. Push excessive igniter wiring back, remount the backplate using the phillips screwdriver. Remount the new igniter using the nutdriver. Remount the bottom door. Put all shelves back. You are done.