22FA-6KLXV8 Magic Chef Microwave Oven Combo - Instructions

I first removed the bottom of the oven and the flame guide to uncover the igniter assembly. Then I applied WD40 to the two Philip head screws and unscrewed them to release the old igniter. The two wire leads from the igniter went into the back of the oven and I could not reach the connection block. So I pulled the oven out far enough to get behind it and took off the panel covering the electrical wires in back. I had previously disconnected the electrical cord from the wall outlet. After I determined that I could not remove the connection block I returned to the igniter and cut the two existing wires close to the ceramic igniter assembly. I marked the top wire with a Sharpie pen so that I would not mix up the new leads when I install the new igniter. Although it was awkward to work inside the small oven space I was able to strip the insulation back about 1/2 inch and then connect the new igniter wires using the twist caps supplied with the kit. I pushed the wires back into the space and added the insulating material supplied. The igniter assembly was then installed with the original two screws and the other oven covers and flame guide reinstalled easily. After reconnecting the power outlet the oven was back in operation with ignition of gas flame within a minute or so. It was a good feeling and now we do not need to consider replacing the gas range.

After removing the oven door, floor, and gas-jet diffuser plate, I could see the valve. There was a shield ov er the elec connections, which I removed. I turned off the gas line to the oven and elec power from the wall, then disconnected the valve. The orig valve had a mounting bracket which I swapped to the new valve( the holes lined up perfectly). I bolted everything back in place, turned it on, and the oven fired right up. I was afraid an appliance this old (1984) would no longer have any parts-availability. but PartSelect came through!

Range is 20+ year old 'condo issue' and difficult to pull from wall since previous owner had tiled it in. Going in from the back was going to be a pain.
Removed the oven door by opening slightly and pulling up. Removed grilles. Removed bottom of oven by sliding 2 latches in the back forward and pulling it up. Removed 2 screws holding igniter (long-style) to the rear of the burner. Cut power to the range and snipped the 2 igniter wires as close to the igniter as possible, leaving me only about 1 inch of wire to work with. Removed 2 screws holding old plate to rear of the back of the interior of the oven. Snipped off the connector on the new igniter. Carefully stripped about 3/8" of insulation off of all wires and used hemostat to hold wires together while applying the wire nuts. Used hemostat to work the wire nuts and excess wire back into the hole. Stuffed the hole with supplied insulation. Attached new back plate with original screws and attached igniter to burner with original screws. Reapplied power to range and did a test light. It worked, so I reassembled the rest. For me, the worst part was holding the wires together so the wire nuts would 'take', while working inside of the oven. But, an easy and successful job!

removed then installed new unit by hand. received order the next day-am. delivery time great.

Purchased 2 piece broiler pan from this site

Pulled the stove out, removed the sides and attatched the new springs( replaced both while the stove was out). Worked like new and put the stove back.

unplug the oven and pull it away from the wall. looking at the oven from the back, the spark module is at the bottom on the lower left. there is a two piece sheetmetal cover over the area of the spark module. use a phillips head screwdriver to remove five screws and the covers come off. the spark module is the blue cube with four push on wire connectors. all you have to do is hold the new one next to the old one and swap one wire at a time. both were clearly marked with identical numbers and letters. really nothing to it. it took me longer to clean the back of the oven than to replace the module. the old module was eaton part number Y-54052-3. the new one is eaton part number Y-054052-34.

removed racks, bottom plate. removed screws with a little bit of help from cooking spray. Unclipped old ignitor clipped in new ignitor, used old screws, and inserted insulation replaced racks, bottom shelf. Turn on oven and worked, been using it for about a week now. PS. ordered on monday morning arrived wednesday afternoon.

With a little adjustment to the mount the part went in ok. Checked the oven works like new; well better than new.

Unscrewed the cover of the microwave replaced the blown fuse with the new fuse, plugged in the microwave and tested all functions and everything worked fine. Thx for quick delivery.

First I unpuged the Range. Then I removed all racks and bottom tray of oven.
The Ignitor is located at back of oven, paralelle to the gas bar. I removed the 2 screws holding the ignitor and unpluged the wires. Then I put on the new ignitor, perfect fit, replaced the 2 screws and pluged in the wires , then pluged in the range. I turned the oven on and it lit in about 10 seconds.
Thank you PartSelect for having such a wide range of range & oven parts . no one should have to pay a service tech. to fix most problems, as long as we have a GREAT SITE LIKE THIS ONE.
p.s. You guy also had one of the lowest prices , my part arrived ahead of schedule .
THANKS A LOT !

Replaced bulb by: 1 pulling plug on microwave to make sure not hot - no power; 2 used needle nose pliers with head part about same size that fit inside of socket; 3 opened pliers and held firm against broken metal part; keeping pressure of pliers against broken metal part of light bulb, slowly unscrewed the broken part from socket using firmly held opened pliers. The rest was a cinch...just screwed in new light bulb, plugged in microwave and viola - there was light once again.

Removed oven door (easy it lifted right off) and remove oven bottom (also easy, no tools). removed two screws holding igniter and unplug old igniter from power. Re-attached new igniter and re-assembled oven.

Parts came very quickly from PartSelect. Good service.

Removed 7 screws on sides and one on top of stove. Replaced both springs (only one was broken but did both). Took around 15 to 30 minutes from start to finish.Fastest shipping in history during holidays without paying anything extra.

It was a bit awkward because the microwave is mounted over my stove. I had to twist around and install the bulb and then replace the cover. It was a bit uncomfortable. It took me about 10 minutes to complete.