Models > 20332C

20332C (310000001-310999999 - 2010) Toro Lawn Mower - Overview

Sections of the 20332C

[Viewing 6 of 6]
Keep searches simple, eg. "belt" or "pump".
Washer-Stepped – Part Number: 614426
Washer-Stepped
★★★★★
★★★★★
(1)
PartSelect #: PS9048394
Manufacturer #: 614426
The Stepped Washer is used to secure the wheels onto the shaft of a push mower. It attaches to the wheel axle. If broken due to wear/fatigue, the wheel will come off and the part should be replaced. I...
$3.99
  In Stock
Baffle-Front – Part Number: 114-7963-01
Baffle-Front
PartSelect #: PS8845729
Manufacturer #: 114-7963-01
$40.23
  In Stock
Chute-Discharge, Side – Part Number: 115-8447
Chute-Discharge, Side
★★★★★
★★★★★
(1)
PartSelect #: PS8847392
Manufacturer #: 115-8447
$18.64
  In Stock
Blade-22 Inch – Part Number: 131-4547-03
Blade-22 Inch
★★★★★
★★★★★
(1)
PartSelect #: PS11804777
Manufacturer #: 131-4547-03
This is a genuine OEM replacement blade for use on Lawn Mowers. If the blade is too dull it will tear the grass instead of an even cut. A bent or damaged blade can cause serious damage or injuries. Yo...
$24.90
  In Stock
Screw-Taptite – Part Number: 95-1726
Screw-Taptite
★★★★★
★★★★★
(1)
PartSelect #: PS9180925
Manufacturer #: 95-1726
$3.99
  In Stock
Bolt-Shoulder – Part Number: 614650
Bolt-Shoulder
PartSelect #: PS9046634
Manufacturer #: 614650
The Shoulder Bolt is a 3/8-16 x 3-5/8 bolt, certified by the original equipment manufacturer. It is a metal bolt which is individually sold and comes in black. Installation requires a wrench or socket...
$4.99
  In Stock
Bearing-Ball – Part Number: 104-8699
Bearing-Ball
PartSelect #: PS8824569
Manufacturer #: 104-8699
$4.99
  In Stock
Screw-Hwh – Part Number: 46-8091
Screw-Hwh
PartSelect #: PS8974798
Manufacturer #: 46-8091
$4.99
  In Stock
Screw-Taptite – Part Number: 32144-1
Screw-Taptite
PartSelect #: PS8950090
Manufacturer #: 32144-1
$3.99
  In Stock
Nut-Lock, Ni – Part Number: 3296-29
Nut-Lock, Ni
PartSelect #: PS9276436
Manufacturer #: 3296-29
The Ni Lock Nut (Nylock Nut) is a Silver, 5/16x18, individually sold metal nut. It can be adjusted and replaced using a wrench or socket and torque wrench to the manufacturer specfications, and is use...
$3.99
  In Stock
Deflector-Side – Part Number: 115-8449
Deflector-Side
★★★★★
★★★★★
(2)
PartSelect #: PS8845543
Manufacturer #: 115-8449
$10.24
  In Stock
Ring-Retaining – Part Number: 32151-61
Ring-Retaining
PartSelect #: PS8950132
Manufacturer #: 32151-61
This metal retaining ring, otherwise known as a snap ring, holds parts in place in your lawn equipment, such as blades, shafts, pulleys, or other rotating components, to prevent them from sliding off ...
$3.99
  In Stock

Questions And Answers for 20332C

Be the first to ask our experts a question about this model!

Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The hub that the mower blade mounts to was broken
The hub that the mower blade mounts to was brokenPut the new Harbonne played and played securing flange bolted it up
Parts Used:
Spacer-Driver Blade Driver Assembly
  • randy from HIGHLAND, IL
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Wrench set
6 of 14 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Wheel height adjuster lever (spring steel) cracked / split in two.
Tip mower onto side, raising side to be repaired. Empty gas tank if possible or use rags to prevent gasoline drips onto clean surfaces.

Remove wheel using a 1/2" socket.
Remove wheel height assembly with 1/2" socket and open end wrench to hold nut below the deck.
Position new spring arm over the slot on wheel height assembly plate. Check opposite side to verify correct orientation if needed.
Remove plastic cover from old lever using a small flat blade screwdriver. Slip onto new lever.
Replace wheel height assembly.
Replace wheel.
Parts Used:
Arm-Spring
  • Ray from YARDLEY, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Socket set, Wrench set
2 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Torsion spring broken
I pryed the apart the torsion spring lever from the handle with a large screw driver. It wasn't easy putting it back, but it worked
Parts Used:
Spring-Torsion
  • Henry from ORLAND PARK, IL
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
1 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!