1VET27DKXGW0 Whirlpool Refrigerator - Instructions

Really easy. Turned the water off, unplugged the fridge and took off a few bolts and swapped the valve out for new. It was basically plug and play. The ice maker started working its next cycle.

Used online resources to deteremine that it was either the icemaker not telling the valve to open or the valve no opening so ordered both and started with the valve (cheaper part). Turn off the water, removed the mounting screws, disconnected the plug, removed the water line (used the wet vac to suck up water while it leaked out). and disconnected the inlet line. Reconnected everything in reverse order but left unmounted until sure it worked, turned water on and waited.

I just popped out the old switch with a flat head screwdriver. Removed the connections and then installed new switch by reversing steps. Popped in back in and the light went on.

Went to PartsSelect. Put in Dishwasher model number. Chose the screws for that model number. Ordered the screws. Can't get any easier than that!

This water valve is slightly different from the original on my older GE refrigerator (i.e., the mounting bracket is larger and oriented differently, thus doesn't fit). To still use the part, I first tried mounting the new valve on my original bracket, but this resulted in a sideways mounting of the solenoid/magnet valve. This orientation generated a slower and noisier water pumping action (the solenoid/magnet valve is assisted by gravity, so it needs be installed with the top of the solenoid facing up). Then I opted to use the original valve plastic housing and bracket and switch out all rubber seals and gaskets and the enitire solenoid/magnet assembly from the new one. This worked like brand new.

removed old ice machine and installed new one
very easy but the old connections were in place and made for easy install

Noticed fan wasn't running, remo ved, verified that it wasn't a sensor, ordered new part, installed new part...works like new. Everything is cold again!

Turn off water supply. Unplug the refridgerator and move so easy access to back. Remember to lower front right wheel to lift rubber foot off ground. Locate valve and remove, note color orientation of wiring (I did not have to remove cardboard cover.) Have a bucket and towel handy because water will spill. Compare the valves to ensure correct part. Apply teflon tape to threads and reconnect hoses and turn on water supply to check for leaks. Then connect power supply and re-attach to refridgerator. Use vac to clean back of refridgerator of dust and build up. Move refridgerator into position and raise front right wheel until rubber foot is back on floor. Use vac to clean coils in the front of the refridgerator. Replace grill. I allowed 4 batches to run before using ice. Pretty simple repair.

Removed old water inlet valve and replaced same with the new one. Installation was easy, parts came quickly, and I now have ice cubes again. Thanks for your help.

I noticed that the refrigerator was having trouble maintaining temperature. Thought it might be time for new one until I found out that a new frig was $5k to $7K. Just happened to notice that the light switch didn't look quite right (was not sitting sqaure to the door). Once I pressed it it came loose. I then realized the the lights were staying on (50 watts of heating). Replaced the switch and the frig started working like new.

After disconnecting the electricity. I followed the instructions as indicated in the "HOW TO" article on the website. I used a steel putty knife and pried the light switch out of its retaining hole. I worked the right side the most since this is the side with the retaining clip. After I removed the switch I transferred the two electrical outlets to the new switch and easily snapped it into place. Engaged the electric power and tested the switch.

At first I went to a local part supplier and they didn't have it in stock but could order it for me for $55.00 plus $10.00 to ship it. I told them I would have to think about it. I went home and got on the computer and found your web site and was I shocked when I saw the same part listed for $6.98 and $7.00 to ship it. You guys saved me $50.00. The part arrived in two day and took 5 min. to install. I now have light in my refrigerator. Thank you.

Used a screwdriver to pry loose the old switch, swapped wires to the new switch and pushed it into the opening. Took about 2 minutes.

removed the 2 screws that held the panel in place, had to reach up and push on locking tabs to lower trhe front of the panel. was able to then push on the locking tab of the switch to release it. removed the wires, replaced them onto the new switch, and snapped the switch into place. the rest was reverse of the uninstall process.

Part was easy to order, delivered quickly, installation very easy. Just unplug the unit, pop out the old swich using a screwdriver, disconnect and reconnect leads and pop switch back in. Definitely recommend that you can do it too.