19844D Frigidaire Refrigerator - Instructions

I removed the cover, used a multimeter to test the compressor circuit, and found the compressor start relay to be defective.
Ordered a new one and installed it when it arrived.

Removed the cowling with a square drive screw driver, removed the spring clip from the cover of the compressor controls with a screw driver, pulled off the old compressor start relay and replaced it with the new part. Since other problems could have caused the compressor to short cycle this was a "replace the part and hope it would work" since that would be the most common reason and it was not a very expensive part.

Simple switch repair: Unplug fridge, pull down to remove switch assembly, slip contacts off. Reverse with replacement switch. HOWEVER, check first to see if the bulb filament might be broken, as this could cause the same symptom. OR in my case, the light socket connection was the culprit. Check that too before ordering a replacement switch.

Twisted replacement bulb into place easily. Let there be light!

After the refrigerator stopped cooling, we determined that the problem was in the compressor area. we used a screwdriver to get the cover off and then vice grips to get the actual pieces out (start relay & overload)--they broke, but they were already broken). We went to the Home Depot site to purchase the parts, but found PartSelect to be much less expensive. Put the parts in when they came a few days later and it worked! thank you PartSelect!

Pulled out the freezer. Unplugged. No freezer back cover was there. The compressor start relay was in a plastic encasement attached to the compressor - wires led me to it. Removed the solid metal spring with a screwdriver and removed the plastic cover. Tried to pull out the defective relay but the freezer was so old I needed a pliers to remove it. When I put pressure on the old relay with the pliers the relay broke and came off in pieces. I then removed the wires from the broken parts and put them on the new relay. I pushed the new relay onto the 2 pins then replaced the cover and spring. After plugging the freezer in the problem was fixed.

I replaced the bulb using my hands to twist the bulb in the socket located at the top of the refrigerator.

The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.

I removed the compressor start relay and replaced it with the new part. Initially it did not work. When I checked my work, I had to tighten the connector on the new part. Once I made the correction, the freezer is freezing normally again.

replaced it

Unplugged refrigerator. Removed control knob and cover. Unwired control and removed same. Removed plastic tube from old capillary tube and placed on new unit. Installed and wired in new unit, making sure new unit was in the "off" position. Plugged in refrigerator, turned control knob to the first numerical setting, and was rewarded with the startup of the refrigerator compressor. Voila!

It was fairly easy to replace the thermostat. Unplug the refrigerator first. Then remove the refrigertor light bulb and 3 screws on the plastic cover that houses the thermostat and defrost timer. Unplug the thermostat from the wiring on the refrigerator and remove the plastic housing holding the thermostat. Remove two screws holding the thermostat and replace with the new one. Put everything back together in reverse order. Unfortunately, this did not corrrect my problem. The refrigerator is well over 30 years old and I had narrowed down the problem to the thermostat because the old one was hard to turn to adjust. About 10 years ago, I replaced the defrost heater in the rear of the freezer compartment for the same problem, and didn't think that would be the problem this time. Well, as it turned out, I checked the resistance on the defrost heater and it was was bad again. I replaced the heater this week I got from PartSelect, and the refrigerator cycles fine now. Replacing the heater is a little more work that changing the thermostat. You have to remove the freezer compartment fan, fan vent, and back inside wall of the freezer section to expose the coils and the heater element. You just need a socket screw driver. Then you have to reach inside and unplug each end of the heater to check it with your ohm meter. A bad element will show up as an open circuit. Then to replace it, you have to maneuver it around to get if away from the coils and remove a couple of clips. Anyone with some common sense can do it, but it can be a bit challenging.