13WN77KS011 (2012) Troy-Bilt Lawn Tractor - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Oil Drain Sleeve
I wish this was longer...it's only about 6", barely enough to have the oil flow past the metal plate of the riding lawnmower. I'm going to figure out a way to make a permanent extension something like this video would be SO much better https://www.youtube.com/watch?v=G9ZVoeqr6R8&t=79s
Parts Used:
-
Laurie from RICHLANDS, NC
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Socket set, Wrench (Adjustable), Wrench set
3 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
upper transmission belt cracked bad
Removed battery, then battery hanger brackets.
Removed the tension spring from under side of seat. That was a little tuff to do. put a long phillips screw driver through transmission pulley.
put a 7/8 box wrench on pulley nut and removed it. took old belt off and installed new one. Reversed order of removal.
Getting the tension spring back into the bracket hole was a little tricky. I used a pair of long needle nose pliers to re install the spring.
cut my yard and I'm a happy camper !!!!!!!!!!!!!!!!!!
Removed the tension spring from under side of seat. That was a little tuff to do. put a long phillips screw driver through transmission pulley.
put a 7/8 box wrench on pulley nut and removed it. took old belt off and installed new one. Reversed order of removal.
Getting the tension spring back into the bracket hole was a little tricky. I used a pair of long needle nose pliers to re install the spring.
cut my yard and I'm a happy camper !!!!!!!!!!!!!!!!!!
Parts Used:
-
William from TRIANGLE, VA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Wrench set
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Didn't line up very easy
Put one side in bottom first and you have to slightly twist the lens to get the other clips to pop in.
Parts Used:
-
michael from eden, NC
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:Less than 15 mins
2 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
light switch broken
Had to pull stove out of the way for easier replacement of the hood switch. Exact replacement part was simple to change.
Parts Used:
-
GINO from MURRAY, KY
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers, Wrench (Adjustable)
2 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bent the old one on a stump
Removed one 1/2" bolt to remove old part .
Slipped new part in place. put bolt in open loop and tightened.
Slipped new part in place. put bolt in open loop and tightened.
Parts Used:
-
George from BAY VILLAGE, OH
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Socket set
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Blade got bend after hit a stump so had to buy new spindle shaft
-
Randall from GALLIPOLIS, OH
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Socket set
2 of 7 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!