Models
>
12A312
12A312 Briggs and Stratton Engine - Overview
Models starting with 12A312
Click on the best match to narrow your results.
- 12A312 ( 0115-E8 ) Briggs and Stratton Engine (Briggs & Stratton Small Engine Model 12A312/0115-E8 (12A312/0115E8, 12A312/0115 E8) Parts)
- 12A312 ( 0118-E8 ) Briggs and Stratton Engine (Briggs & Stratton Small Engine Model 12A312/0118-E8 (12A312/0118E8, 12A312/0118 E8) Parts)
- 12A312 ( 0115-E1 ) Briggs and Stratton Engine (Briggs & Stratton Small Engine Model 12A312/0115-E1 (12A312/0115E1, 12A312/0115 E1) Parts)
- 12A312 ( 0100-E1 ) Briggs and Stratton Engine (Briggs & Stratton Small Engine Model 12A312/0100-E1 (12A312/0100E1, 12A312/0100 E1) Parts)
Keep searches simple, eg. "belt" or "pump".
Starter Pawl-Ratchet
PartSelect #: PS8942598
Manufacturer #: 281505S
The manufacturer-approved Ratchet Pawl (Starter Pawl) comes in a set of two (2). This part attaches inside the recoil assembly, and is used to engage the flywheel. if broken due to wear/damage it will...
$3.99
In Stock
Kit-Needle/Seat
PartSelect #: PS8963322
Manufacturer #: 398188
This needle and seat kit, also known as a float valve, is found in many types of liquid-fueled lawn equipment, such as carburetors. The valve regulates the flow of fuel into the float bowl. The needle...
$6.91
In Stock
Fuel Tank
PartSelect #: PS9141053
Manufacturer #: 799863
This is a replacement fuel tank for your outdoor power equipment. It is made of black plastic and comes with the tank itself, as well as the fuel cap. The fuel tank stores fuel before it is transporte...
$98.07
In Stock
Seal-Oil
PartSelect #: PS8948679
Manufacturer #: 299819S
This OEM Oil Seal is an individually sold rubber part which is attached around the axis shaft on the crankcase housing to provide a proper seal. A broken seal will lead to a leak, and the part should ...
$5.99
In Stock
Common Symptoms of models starting with 12A312
[Viewing 1 of 1]
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Mistreated Briggs & Stratton 206 CC Engine on MTD Chipper
Removed tank and drained old gas.
Removed and disassembled carb. Needed new gaskets and seals, and had to clean corn syrup glaze (separated ethanol) from bowl and everywhere else with carb cleaner.
Throttle linkage was de-plating/rusty. Steel wool and WD40 got it moving again.
Cleaned spark plug electrode.
Reassemble ... Read more d, poured Sea Foam in the bottom of the tank and gave it a few pulls.
Let Sea Foam sit for a while, then filled the tank with Premium.
Blew white smoke for a minute then ran like new. Shredded for a while, then changed the oil.
Removed and disassembled carb. Needed new gaskets and seals, and had to clean corn syrup glaze (separated ethanol) from bowl and everywhere else with carb cleaner.
Throttle linkage was de-plating/rusty. Steel wool and WD40 got it moving again.
Cleaned spark plug electrode.
Reassemble ... Read more d, poured Sea Foam in the bottom of the tank and gave it a few pulls.
Let Sea Foam sit for a while, then filled the tank with Premium.
Blew white smoke for a minute then ran like new. Shredded for a while, then changed the oil.
Read less
Parts Used:
-
Dana from HAMMOND, IN
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Pliers, Screw drivers, Socket set
3 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Generator would not start, Birggs & Stratton recommended to replase Gasket Exhaust.
Remove the spark suppresser, 4 face screws, 2 bottom screws and the two screws the hold the gasket. I also had to back out the top screw of the cover it blocked and prevented the removal of the gasket.
Parts Used:
-
Alberto from PALMETTO BAY, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Socket set
7 of 23 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!