12001747 Maytag Ice Maker - Instructions

Removed the screws that held the main ice bin and slid back the bin to leave space behind the auger to remove the broken ring. Replaced with new ring and replaced screws to hold ice bin back in place.

Removed all screws on back and 4 on front. That part is easy IF you have a Torx of the right size. Slip out the ice bin a bit and replace the drive ring. Reassembly is a bit harder since some internal shift can occur -- rotate or tilt the whole assembly to get two -- I think -- screws started. No need to over tighten screws; snug is good enough.

Removed drive assembly end of ice bin using socket wrench to get to old ice bin drive ring. Pull drive sssembly back to get ice bin ring out of the other end of ice bin. Installed new ice bin ring and and reinstall drive assembly end.

the drive motor was broken free from the tray, so I just changed it over and replaced the drive ring very esay for me

My son-in-law is our handyman. He diagnosed the problem, found us the part and then put it in. The part came several days before we expected it and the whole thing went very well and we saved lots of money!

looked a website removed part found broken item order and installed in 15 minutes, easy simple fix very low cost change

rl

The most time-consuming part was removing the screws. First, remove the 8 screws that attaches the ice bin to the front cover. This will free up the auger enough to pull up the back end where the drive ring is held in place. The ring just pops right out. The only thing I recommend is as long as you have the bin out (and empty), go ahead and give it a good wash. Make sure it is thoroughly dry so that no ice freezes to the moving parts.

I read what other people had done so I tried the easiest solution--Forced, without breaking, the plastic & fit the ring right where it needed to be.

Remove 2 screws, and GENTLY remove tray. There are two motors on the back side that are wired in to the back of the fridge. Unplug the harness and the whole assembly will come out. Take note of the way the plunger comes out, if not, it will take a little more time to figure out. reassemble motors onto new tray then GENTLY slide into postion, with one hand plug in wiring harness then seat tray into position and reinstall screws. Done.

To replace the broken drive coupling on the motor end of the auger requires sliding the ice bin out of the freezer section of the refrigerator. Remove the ice cubes and let it thaw out for a few minutes. Remove five screws holding the front face on the ice bin to remove the ice auger. slip the new drive coupling over the end of the auger. reassemble and replace the face plate with the five screws. Slide the ice bin back in the freezer. Less than fifteen minutes it was finished.

remove ice bin,remove 1 screw on bottom of left side of enclosure, unhook harness and remove entire enclosure incuding auger moter. remove screws that hold auger motor to enclosure. remove screws holding solenoid to enclosure. re-install in reverse order, very simple repair. ordered part on monday afternoon it was on my doorstep on tuesday morning. very speedy delivery was really impressed , thank you very much!

Problem caused by ice cubes falling out of ice bin and collecting at rear and interfering with ice dispenser drive. Broke plactic drive ring. Pull down 2 clips at front bottom of ice bin. Pull ice bin out. Dump ice cubes. Remove 8 star drive screws to allow case to move far enough to clear broken drive ring. Replace drive ring. Reinstall and tighten 8 screws. Install ice bin. Correct loose right side ice cube retainer board to prevent cubes from falling out of ice bin.

removed torx screws and replaced ice bin drive ring.

Easy repair - Don't over complicate it. 1) Flip up ice bar to stop making new ice. 2) Pull out the complete ice bin/tray. 3) shut freezer door while you work on the ice bin. 4) All you need to do is remove the 4 screws holding the ice bin holding tray to the front of the Ice cutting section in the front. 5) Screw drive can then be pulled forward to remove the old/broken white drive cap. Just replace the White Drive ring, put the drive screw back into the ice bin tray and re-install the 4 screws. 6) When re-inserting the bin, you may have to twist the screw drive slightly to re-align with the motor bracket in the back of the freezer. Suggestion: throw out old ice because if it is wet or slightly melted, when you put it back in the freezer the ice will freeze/clump together into a large ice clump; not cubes. Also dry out the ice bin so there is no water to freeze up or create a new jam when the ice bin now re-freezes.

The only hard part of this rapair is getting the auger off the motor. I wasted a lot of time before driving to auto supply store and buying a set of thin needle nose locking plyers so I could get a true grip right behind the auger. Once I had that, it was just a matter of a lot of brute force and a second pair of big locking pliers I already had for grip on the auger.