Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 12-6663-66-01 > Instructions

12-6663-66-01 Tappan Wall Oven - Instructions

All installation instructions for 12-6663-66-01 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the wall oven repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 12-6663-66-01
151-165 of 212
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

oven wouldnt heat up but stove top still worked

  • Customer: richard from PLAINVILLE, CT
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
ge gas oven that i've had for over ten years without any problems just stopped heating up even though i could see the igniter glowing red. once i was able to determine or "lucky guess" it was the igniter, i pulled the power plug so i couldn't get zapped. i took out all the drip pans and covers inside the oven to access the igniter. i then proceeded to remove the broiler drawer and disconnect the wires underneath. two screws on the igniter and was able to remove the bad one. now working on my table i cut the wires off the old igniter and spliced them with the supplied wire nuts (x2). i also felt better wrapping them after with electrical tape for my own added security. installed the new igniter and reconnected the slide clips under oven ,put all of the drip pans, etc back in the same way it came out. plugged it back in and double checked all of my connections and made sure there was no gas leaks, and everything worked beautiful. cost me $50 for the part that took only 2 days to get after i ordered, and about a half hr of my time with basic handyman skills. thanks parts select!!!!!!!

Gas Heating Element would not ignite

  • Customer: Raymond from Durham, NC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Disconnected the electrical supply to the Oven. Removed Oven base heat shield by unscrewing thumb screws in the back of the oven. Removed secondary heat distribution plate from the gas burner by unscrewing two self tapping metal screws on the front of the plate and unscrewing the retaining nut in the center of the plate. Removed two stainless steel retaining screws holding the oven igniter, cut the electrical wires to the igniter removed the fiberglass insulation tubes from the existing wires and placed them on the new igniter wires. Routed the new electrical wires through the access in the bottom of the over where the original wires came from the control circuit. Reconnected the new electrical leads to the previous leads using ceramic wire nuts supplied with the igniter. Reconnected electrical supply and tested oven igniter to ensure it would heat and ignite the gas oven burner. Reassembled the heat distribution plate onto the oven burner. Reassembled the oven base plate. Note: Replaced the oven light during the repair cycle.

The oven stop working.

  • Customer: Luis from Chatsworth, CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
Right part, right instruccions= succesfull repair.Thank you.

oven would not lite

  • Customer: Edward from Buffalo grove, IL
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
removed bottom oven panels and removed ignitor ,then cut wires on bad ignitor as close as possible.taped new ignitor to old wires and pulled them through the bottem of oven and made connections.

Igniter would glow but stove would not light

  • Customer: scott from kansas city, MO
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Socket set
  • 0 of 0 people found this instruction helpful
I actually read the first post, then ordered the part. The part showed up very quickly. I removed old part, attached new part with the ceramic wire nuts and put back together... Literally took 5 minutes and now works great...

oven would not light.

  • Customer: Jeanette from Freeport, TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
replaced old part with new one and fixd the problem.

Oven Would Not Light

  • Customer: William from Cinncinati, OH
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I followed past on-line repair reviews by prior customers, who problems were nearly identical to mine. It was basically an extremly easy repair. Those reviews/notes are great, leading to using partselect as a valuable start source for parts replacement. (I removed the part before ordering for assurance of getting the correct item. )

Oven would not light.

  • Customer: Bill from Cleveland, WI
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I called the repairman, and he said parts were no longer available for this appliance. He charged $85.00 for this advice. As soon as he left I looked on the internet and found your site and looked for the part. I found it right away, ordered it, and installed it. It was easy to install and it works great. The repairman candidly told me that new ovens are not near the quality as mine is and that is why I didn't want to buy a new oven. Thank you for providing an alernative to our throw-away society. Bill

Oven Did Not Heat

  • Customer: Sandra from Los Angeles, CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
The oven began to have low heat and then no heat. Read about it on-line and figured it was the igniter for the oven. Found the model number on stove/oven frame behind the bottom draw. Then I looked at a few on-line videos about how to install the piece. I have a convection oven and had to take the fan cover off to remove the bottom inside cover of the stove and I couldn't figure out how to remove the oven door to make it easier...so I had to leave the oven door on the stove. The stove door is heavy so be aware of that issue. Also I needed help...it was a two people operation. I needed to lay the stove on it's back to get to the piece. I needed to cut the wires and remember where everything went it was as simple as the video made it out to be...there were a few more wire connections. There is the issue of the door ...be careful you can stand the stove up and bring it down again but if not be careful/mindful of the door and it's weight and desire to slam closed...maybe a third person would be good to have around. ;) Anyway it can be done. Have patience. Take your time. Have a buddy to help you. Best part...the oven is now heating!! ;) Lovely!

upper oven would light up but took awhile

  • Customer: robert from des plaines, IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
disconnect electrical power to oven , removed face plate to where the igniter connections were. lift cover that is over the igniter in oven, remove igniter from burner, attach ner igniter to burner and route wires inside cavity where connections are. cut connector from old igniter leaving enough wire to splice to new igniter, strip wire and connect using wire nuts, put everything back together and test

oven took very long time to ignite.

  • Customer: Ronald from Keymar, MD
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
first we went online to see if others had experienced the same problem, and what they did to fix it. ordered part to arrive within three days. husband removed connecters from old igniter and spliced them onto new one. We felt it should have come with connecters. set burner with new igniter in place, and it worked...Yay! just in time for Thanksgiving turkey!

Igniter glowed but slow or no oven lighting

  • Customer: JAMES from Harrison, MI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Replaced the igniter.

oven wouldn't light

  • Customer: Donna from Trinidad, CO
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
using socket set removed old ignitor,replace with new one and secured using the socket set. The oven lite right up.Service was A1. I ordered on Friday evening and the part was delivered on Monday. Thank you.

Oven would not light

  • Customer: Edward from Pent Water, MI
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
Put a new ignighter in the oven I also would like to commend PartSelect for the fast service on the part i ordered it one day and recieved the part the nexted day i would recommend you any time

Oven lights intermittently, smell of gas

  • Customer: Robert from Lakewood, NY
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Model# GLGF366ASD range
Turned off breaker
Removed oven door (see gas range manual for procedure)
Removed storage drawer on bottom of range.
Removed oven racks.
Removed oven bottom panel (2 screws in back of panel)
Removed oven shield (screw on left and right front of panel & nut in middle of panel)
At this point igniter was exposed
Removed igniter by removing the 2 self tapping screws securing igniter.
Note: threads on both screws stripped during removal, requiring both
screws to be cut off for removal.The stripping of threads of these screws
is probably normal due to the heating and cooling of the oven during
operation, making the threads on the screws brittle.
Marked the top wire on the igniter with a black sharpie
Cut both wires as close to the old igniter as possible.
Cut wires on new igniter about 10" long.
Connected new igniter with wire nuts (provided) making sure to connect wire from top of igniter to wire marked with sharpie.
Installed new igniter using 2 new #8x1/2" self tapping screws.
Pulled excess wire & wire nut connections down into the back of the storage drawer area making sure wires were resting on flanged area of panel.
Reinstalled oven shield, panel, racks, storage drawer, and oven door.
Turned breaker back on.
Oven works great.
Note: self tapping screws should be provided
All Instructions for the 12-6663-66-01
151-165 of 212