Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 1151WL-36G > Instructions

1151WL-36G Hoover Cooktop - Instructions

All installation instructions for 1151WL-36G parts

These instructions have been submitted by other PartSelect customers and can help guide you through the cooktop repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 1151WL-36G
31-45 of 82
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Drip bowls very dirty and stained

  • Customer: john from donna, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
Remove burner elements. Remove old drip pans. Thoroughly clean stove top under drip pan edges, and under top cover. Install new drip pans. Install burner elements.
I never seem to be able to find the correct replacement drip pans at retail outlets in the quantities I need. Your parts identification, selection and ordering processes were simple and delivery was faster than I hed expected.
Thank you

Old burner pan warped.burner sat at 15 degree angle.

  • Customer: Michael from Portland, OR
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
Removed burner and then burner pan.Then replaced pan and reinstalled burner.

replaced old drip pans

  • Customer: Frances from Summerfield, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
Fastest, easiest thing I have ever done! I got my orders so fast it was unreal! Hurrah for good old American know-how. I will always recommend these good people!

Receptacle had become bad poor connection.

  • Customer: JAMES from Harrodsburg, KY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 1 of 3 people found this instruction helpful
First I disconnect the breaker. I removed the defected receptacle and cut the wires. I connected the new receptacle with parts with the new part. Turned the breaker back on and everthing worked fine.

Bowl -Drip and gasket

  • Customer: Walid from Worcester, MA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
it was relay easy when you get the right pats .so
Thanks for .
PART Select.
Best regard .
Walid

one of wire melted and broken off from receptacle

  • Customer: Young from Cordova, TN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 1 people found this instruction helpful
Cut broken wire and existed wire off and put splice on both new and old wires to connect them.
It's easy job.

Sockets for the burner elementss were burned out

  • Customer: Martin from Manchester, MD
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
I removed the burner elements for three burners by lifting the surface top and unplugging them. I snapped out the plug sockets that were burned out and cut the two wires, one element at a time. Using the included wire nuts I stripped the ends of the cut wire and connected each wire to one of the wires on the new socket. Once the wires were connected I snapped the sockets in place and reinstalled the elements, lowered the surface top and the range was ready to use.

Electrical receptacle for burner was defective.

  • Customer: gerald from Hillsboro, TN
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 1 people found this instruction helpful
After buying a 'universal' part at Lowe's and it not fitting correctly and shorting out the burner, I went online and found this source for an exact replacement part. Beside having to disassemble the drop in stove burner two or three times it went well when I had the correct part. I lost one screw somewhere and that delayed me a short time to find a replacement. Thus the 1 to 2 hours. It would have been about a 30 minute job if I had been smarter.

The burner was shortening out and would work sometime. The first time I replace the burner but the new one shorted out quickly.

  • Customer: shawn from Vancouver, WA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 2 people found this instruction helpful
I unplugged the stove. Took out the burner and removed receptacle by pulling it out of the bracket and clipping the wires. One thing you want to make sure is that when you clip the wires from the receptacle you're replacing you leave enough wire so that you can connect them to the wires on the new receptacle when it is in place on the stove. I had just enough but would have liked more. The bracket I received didn't match the one on the stove so I used the one on the stove since the receptacle itself was the same as the one I was replacing.

burner not operating or intermittently

  • Customer: Elroy from Atwater, MN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Shut off power at breaker box. Removed top burner unit. Removed old receptacle (Mounting screw was rusty so I drilld out the old one.) Cut wires from old unit. Stripped wires back on old unit. Attached old and new wire with ceramic wire nut. Attached new unit. Reinserted top unit. Reconnected power and "voila". Wife was smiling again.

needed a new drip bowl and couldn't find ons that fit exactly but you had it

  • Customer: Elsie from Garner, NC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I removed the old one and put in the new one. Works great!!!!!!!!!!!!

Burner receptacle had malfunctioned and been removed

  • Customer: Kerry from Silverado, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
10 Minutes for a stove my landlord thought was not fixable (repairman had already cut the wires to the element and capped them)! The delivery person handed me the package, I got out the single tool needed, installed the part, put away the tool, cleaned my hands, and put a pot of water on the stove to boil for pasta. 10 minutes!

Electric surface burner would only turn very hot

  • Customer: Vittorio from Wakefield, MA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Well, I had to search a bit deeper in the internet to find out that the problem was not with the surface burner (which did look a bit burned out anyway) but rather with the surface burner switch (Part Number: PS336885) which must have ben damaged by the heat of the closest burner. If this problem would have been better documented (or if I would have searched more carefully) I would have saved over $40 with parts (Surface Burner Receptacle Kit) that I didn't quite need. Repairing the switch was very easy, thanks also to the available video , even though the stove used on this video (front panel) didn't quite match mine (top-back panel).

To Old Needed To Be Replace

  • Customer: ROSARIO from MESQUITE, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Actualy I just removed the old ones and replace them with the new ones . And thank you for your prompt delivery I found some one I can trust . Thanks again . Mrs bolanos

rusty pans

  • Customer: Stewart from Hanover, PA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
simply remove the old and install the new; perfit fit
All Instructions for the 1151WL-36G
31-45 of 82