Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 1111WAW Maytag > Instructions

1111WAW Magic Chef Range - Instructions

All installation instructions for 1111WAW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 1111WAW
166-180 of 231
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Oven would not stay up to heat; slow to heat

  • Customer: John from Hamilton, VA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Followed the excellent instructions on your web site. I removed the oven burner assembly to make it easier to install the new igniter. The connector on the new igniter matched the one in my oven exactly. It helps to have the oven light on!

Gas would turn on but oven would not heat

  • Customer: kevin from kansas city, MO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
There was a lot of trepidation about starting this project. What if this is the wrong part? What if I hook it up wrong? What if the gas line is not properly secured when I'm done? This is why it took my 6 months to start this project. I hesitantly looked up my product number online and partselect.com returned three of the top ten results so I clicked it. One of the best moves I've made. When the product was shipped, I received an email with a video attached that explained how to install the igniter. This is what set partselect.com apart from everyone else and differentiated my experience from a "maybe i'll look around more next time" to "I will use partselect for all of my appliance part needs from now on" experience. Thank you for the quality customer care.

Oven takes very long to heat, sometimes did not reach temperature, gives smell of gas

  • Customer: Joseph from Croton on Hudson, NY
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Remove oven door and bottom panel. Remove metal shield above the burner. Unscrew old igniter from brace. All this was straightforward. Then I found the old (long) igniter did not have a convenient plug that I could pull through the hole in the back of the oven. So I had to clip the two wires to remove the old igniter and stripped the insulation of these wires. Then I clipped the two wires of the new igniter since, unfortunately, I could not use the convenient plastic connector. I stripped the wires of the new igniter and connected both to the previously stripped wires coming through the hole from the back of the oven. I twisted on the ceramic wire nuts provided. It took 10-15 minutes or so to be confident these wire nuts wouldn't just fall off on their own. Then I stuffed the wire nut connections back through the hole, stuffed in all the insulation provided (necessary for the new (short) igniter!) and screwed the new igniter to the old brace. (I didn't need the new brace supplied or two long wires supplied.) Total time was about 70 minutes. The oven works well! This experience is much better than finding a repairman, scheduling the visit, etc.

wouldn't heat, flame would'nt start

  • Customer: randy from midvale, UT
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
look up part, read the diognosis, order part, watch repair vidioe, order part, install mystelf. success!

shorted out wires from previous owner install, on the igniter

  • Customer: mark from peoria, IL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
it was really simple with the kit and instructions that came with the kit everything i needed was in the kit, and hats off to you guys

oven would not bake

  • Customer: James from Carnegie, PA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
followed video took 10 minutes, almost went anf bought a new stove

Oven would not ignite

  • Customer: William from Cottonwood, AZ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The only difficulty with following the supplied video, is that my ignitor did not come out as easily as a few turns of the screwdriver. The screws stripped as I tried to remove them, making them twirl in their holes. I had to apply back pressure for them to come off and free the ignitor for replacement. Other than that, the installation went smoothly, and the oven sprang to life within 10 seconds of turning it on.

Oven was taking too long to reach desired temperature as well as emitting gas fumes.

  • Customer: EARL from NEW YORK, NY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I simply followed the "general" instructions from the online video "Partselect" provides and perused the instructions included in the kit. The OEM igniter was much longer than the replacement but the new part was spec'd just fine. It was necessary for me to open up the back of the stove in order to retrofit the igniter leads to the original block connector and install the heat resistant padding included in the kit. The additional necessary hardware fit very nicely inside the oven. The stove's oven fired up without any problems and spared me the expense of purchasing a new oven. Thank you very much "Partselect".

The igniter on the oven would glow but the gas would not light

  • Customer: Jim from Harbor City, CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I removed and replaced the igniter. I described these symptoms on the web site and it detailed that90% of the time by installing a new igniter it will fix the described problem. So I ordered the part and installed the part and everything worked OK. The only tool I had to use was a screw driver to remove three screws. It took about half an hour. If I had to do it again it would take about 15 minutes.

Oven would not heat

  • Customer: James from Woodward, IA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Unplugged oven. Removed door,racks,and bottom shelf. Removed screws from ignitor and unplugged it from connection. Installed new ignitor with screws and plugged in to connection. Tucked wires behind insulation as they were before. Installed previously mentioned items and turned on to check. Worked great and am very pleased with PartSelect and the assistance they offer.

Oven would not heat

  • Customer: Roger from Bluefield, WV
  • Difficulty: Really Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Ordered oven Igniter kit PS1573892 which cost $73.00. Received the kit with instructions easy to follow to install. I was surprised how easy it was to repair, with the help of my wife we did the job in about 2 hours, the oven now works great. I really saved a bundle of money doing this myself, a local repair service wanted $114.00 for the same part and $200.00 labor to install and this is the gospel truth. I am 96 years old. RMA Bluefield, WV

Oven would not Light

  • Customer: Dan from Clifford Township, PA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Take off oven door, remove racks, lift out bottom plate of oven, remove deflector shield, unbolt old igniter gently fish out the wire and plug from the back of the oven. Unplug and replace with the new igniter. re-assemble oven.

slow to get to temp and slow to light

  • Customer: Michael from Hartland, WI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Followed the directions on the video. Very easy to do.

Light burned out in upper oven

  • Customer: Shirley from Las Vegas, NV
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Screwed in light bulb and glass protector

Replace an old igniter

  • Customer: Jacob from Agoura Hills, CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Make sure power to the oven is disconnected. Remove all shelves. Partially open the bottom door and yank it out so it is out of your way. The igniter is next to the back and upper wall of the oven inside the lower (broiler) compartment. The igniter is held by two screws which I opened using a 5/16 or 8mm nut driver. After removing the two screws, remove the back plate using a regular phillips screwdriver. Next, pull out the two igniter wires until the connector comes out. Pressing the side tabs disconnect the igniter from the connector. Connect the new igniter. If nesessary, replenish some of the insulation with new insulation that arrived with the new igniter. Push excessive igniter wiring back, remount the backplate using the phillips screwdriver. Remount the new igniter using the nutdriver. Remount the bottom door. Put all shelves back. You are done.
All Instructions for the 1111WAW
166-180 of 231