Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 11072622100 > Parts

11072622100 Kenmore Dryer - Parts

All parts for the Kenmore Dryer 11072622100

Below is a list of all parts for the Kenmore Dryer 11072622100. To find the repair part you need, you can browse the list below or you can narrow your choices by searching for a part by name or description.

All Parts for the 11072622100
1-14 of 117
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$8.98

Thermal Fuse

This thermal fuse is designed for use in dryers. It is a safety mechanism that stops the flow of electricity to the heating element when a dryer overheats. When this fuse is faulty...

$14.56

Multi Rib Belt - 92-1/4"

This multi rib belt is an important part in your dryer, it is what helps rotate the drum. The belt attaches to the drum, idler pulley, and motor pulley. As the armature of the motor rotates, the belt begins to move and turns the drum. If you notice the drum of your dryer is not spinning during the dry cycle, but you hear the motor running, your belt may have snapped and it will need to be replaced. This belt features four ribs and three grooves, however it replaces a wide variety of belts including wider styles that had five ribs and four grooves. When installing this part make sure the grooves are facing down, against the drum. This replacement part is 92 1/4 inches in length, and 1/4 inch wide. Before you begin any repair work, make sure your dryer has been unplugged.

$14.81

Door Switch - 3 Wire

A door switch is a simple on/off switch mechanism that prohibits the dryer from operating when the door is open. This part may need to be replaced if you find that the dryer is not...

$14.96

Thermostat, Internal-Bias

A cycling thermostat is in tune with the temperature of your dryer and regulates it in order to maintain a certain temperature. This thermostat reaches a temperature of 155 degrees and will then turn off and then on again once it has dropped by 25 degrees. If your dryer is not giving off enough heat, is over-heating, is not turning on, or is having issues with the timer functionality, this could indicate an issue with the thermostat. The installation of the cycling thermostat is simple and the only tool required is a 1/4 inch nut driver (and gloves for safety).

$3.56

Door Catch Kit

This is a door catch kit, and it is designed for use with your dryer. On your appliance you will find both a strike and a catch, these two parts work together to keep your dryer do...

$21.73

'M' Series New Style Coil Kit

This is an M series new style coil kit, used in gas dryers. When the igniter reaches a high enough temperature, these coils work together to let the gas enter the dryer. The coils open the gas valve; if the valve does not open the heating element will not ignite. Both coils must be operational for the valve to open. This is a safety mechanism to ensure that there are no unsafe buildups of gas inside your appliance. This kit comes with a three-terminal boost/hold coil, and a two-terminal main coil. Each part is approximately 1 1/4 inches in diameter. If the igniter glows but shuts off without igniting gas, it means one of both of your valves is faulty. We recommend you replace these as a set. Before you begin this repair unplug your appliance and shut off the gas supply.

$12.47

Rear Drum Support Roller Kit

The drum support roller kit allows the dryer to tumble properly by supporting the drum cylinder. The kit includes two drum rollers, four tri-rings and one palnut (or retaining wash...

$17.97

Igniter Kit

If your dryer will not heat, takes too long to dry, or does not provide enough heat, you might want to replace your igniter kit. This silicone carbide igniter with ceramic holder kit includes the 3-inch flat igniter, bracket, 4-inch wire leads, and the plug. The kit can replace both round and flat igniters and is used for many gas clothes dryers. Be sure to disconnect the power source from your dryer before you do this repair. The igniter is located within the burner assembly, so you will require tools to complete the repair. You will need a putty knife, a small flat blade screwdriver, a 5/16 nut driver and a 5/16 socket with a ratchet.

$10.04

Idler Pulley Assembly

This part provides the tension required for a multi-ribbed belt. It also serves to help the belt to rotate the drum and attaches to the idler pulley wheel. If your dryer will not s...

$33.09

Lint Filter

This filter collects lint as it passes through the dryer vent. Note: This part has been updated by the manufacturer. It may appear different but will still function the same as the original.

$5.76

Tri Ring

If you notice that your dryer is noisy or will not tumble, you may need to replace the tri ring. This part is triangular, and is less than an inch in size. Tri rings can be found b...

$27.70

Radiant Flame Sensor

If your gas dryer is not heating up or igniting, then replacing the flame sensor, located in the burner assembly, could solve it. This part senses heat from the igniter to monitor if it is hot enough to ignite gas to light the burner. Once the igniter is hot enough it will open the valve and allow gas to flow. This is a safety mechanism to prevent dangerous levels of gas from building up. To repair, the main top of the dryer should be lifted, as well as the front panel to access the component. This flame sensor assembly is made of both plastic and metal.

$5.84

Leveling Foot

If your washer shakes or vibrates loudly when it reaches its max speed, check that the leveling legs are even. To ensure that the washer is firmly on the ground using all four legs...

$29.24

Drum Felt Seal

Includes adhesive.

All Parts for the 11072622100
1-14 of 117