1106818610 Kenmore Dryer - Instructions

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

It had been making noise for a week and I bought the two drum support rollers hoping that was the problem. It wasn't as the dryer started shutting down after a few minutes of running. I opened the top of the dryer and removed the 2 screws holding the face and door on. I removed the face and disconnected the door switch wires and released the drum belt by pushing on the idler pully. I then removed the drum straight out the top. I then put a wrench on the fan on the back of the motor and unscrewed it and then released the two holdown clamps on the motor and removed the motor. I had to make a couple of wiring modifications for the new motor but the instructions and connectors that came with the motor were perfect. I put everything back together and plugged the dryer back in and tried to start it and .... Nothing. I forgot to reconnect the door switch wires. Fixed that and the dryer now runs as good as new and makes no noise at all now (almost anyway). It should be good for another 10 years easy.

all that was required was to push the catch into the slot notools needed.

I realized from this issue years ago that it was porbably the heating element. I took the dryer to the garage and remove the back and figured out how to get the heating element out. Once I had it out it had a break in the coil so I knew I needed that part. I hit parts select on line and ordered the part. I left everything in the garage and waited for the part. In a couple of days it came and I put it in and took the dryer back to the laundy knook, gave it a test run and Its all good!

You can buy the switch AND lever/latch, but partselect had lever by itself which is all I needed. Pay attention to orienation of lever around switch when you take old latch off and attach new. Also, be careful to not drop new lever behind/beneath clothes dryer drum. Took my wife and I a while to fish it out. I have replaced heating element, and other parts. At some point it will be time for a new dryer...

I followed the on-line video. I am extremely happy I made the effort and successfully fixed my dryer on my own. It sure beats a new dryer expense or high repair cost.

After removing the back (five nut screws), lifting the top (two lint filter screws), I diagnosed the problem (timer, fuse and sensors tested OK - heating element broken). I uninstalled the heating element cage sensors (three nut screws) but did not unwire them. Then I removed the heating element cage (one nut screw on top and lift) - the right angle screwdriver was very helpful. I removed the broken element (one nut screw on bottom). Ordered from Parts Select online because they had the element for a better price & quicker expedited shipping than Sears. As soon as the part arrived (two days!), I rewired and installed the element and assembled the dryer in the reverse order of the above process. Total time from package arrival to drying clothes (BIG stack) - 30 minutes!

just like the guy in the video. It was easy to folow his instructions, and the best thing of all i could stop the video if I had a question and then resume!

The original lint filter was broken, as the dryer was very old I did have the part #, I searched the internet I saw partselect.com on the search engin I did know it would be so easy to get this product, I selected the part by size specification.

Thank you partselect .com for making my life easy. Or else imagine me driving around looking for stores which sell spares for old dryers wasting time and gas-go green shop at home.

re-placed screen

found a video online and followed the instructions. First unplug dryer, then take off back cover with a 1/4 inch socket unscrew the 5 screws from the cover and remove back. Then with a ohms meter you have to check to see what terminals are bad. In my case it was the heating element. So, next you go to top of dryer and unscrew the lint trap so you can lift the top of dryer and remove the bracket holding the housing where the element is located. First take off the leads that are connected to the element and housing unit. Then gently lift housing unit up off the hinges and pull it out. Then turn over and there is another screw that holds the heating element in. After unscrewed the element pulls right out and then just put new element in and reverse everything.

I follow the instructions from the video you guys show the only issue is putting back the tensioner in place but my brother leaves next door and help me.

Undid the back, remove wires going to element, unscrew lint trap, pop the top and undid the nut-screw holding the element housing. pulled out the bad element and did everything in reverse with the new element... unplug it first though because I left that step out.

It went well, I followed the instruction video and referred back to it if any questions or difficulty. The instructor on the video was obviously very experienced and duplicating his actions exactly was very helpful, One thing I noticed that wasn't mentioned was that the thread on the wheel / motor is left handed.

I watched a U Tube video about banging sound from dryer. Once I recognized the problem, lifted the top, removed 2 screws holding the front, removed the drum, and bingo. Saw the worn out drum roller. Ordered the replacement parts from "PartSelect" on line (Great Company). Was in no hurry, so I chose regular mail delivery. 4 days later, got the correct replacement parts, put the dryer back together, and now, the dryer is quieter then when I bought it new, a thousand years ago. I will never again be afraid to tackle an appliance issue. THANK YOU !!!