11067851600 Kenmore Dryer - Instructions

The repair was fairly easy. The most timely part of the repair was removing the twelve screws from the back panel to expose the repair.

Removed the back of the dryer. Used a multimeter set to read Ohms to check each Thermal cut-off switch. Each one read with continuity and some resistance. The one that was bad read open. So i replaced this one and the other one that came in the kit since i already paid for both.Then i replaced the back ran the dryer and it worked great.

The old catch on my dryer door was gone and I was keeping the door closed using tape. I ordered the part and it arrived with no hassles in about 5 days. The repair was too easy. I just popped the new catch in place. It took all of about 30 seconds to complete using no tools. I wish all home repairs were this easy.

Removed the old one and installed the new one! What impressed me the most was the amount of time for delivery, one day! Actually it came before 24 hrs!!! Very impressive! I would highly recommend this company!!!

I recommend you order the idler pulley as soon as you start to hear the unusual noise indicating metal against metal. Replace the idler pulley before it fails and possibly causes more damage to the drive system. Simply removed the power cord at the back of the dryer and then the multiple screws holding the back panel in place as well as the clip holding the exhaust vent in place. You may need to remove the top panel to access a few of these screws. A diagram of the belt routing is in the paperwork I found behind the front lower panel of the dryer. This too is easily removed with just a few screws.

I first went to your site and studied the parts diagram to see where the element was located. I then unplugged the dryer and pulled from the wall. After that I popped open the front cover and accessed the bottom of the dryer where the element was located. I then removed two screws that held the element in place and removed the wires to the element. After a little tug the old element came out. I slid the new one in place and connected the wiring and screws and replaced the cover and pluged it in. Works good as new...

Had to remove the back of unit to access the area of subject part by removeing 12 to 14 screws also the gas line had to be removed. Two screws held the part in place. Unit now runs normal.Saved alot on repair costs!!!!!

Removed old filter and put in new one.

somthing fell down in the blower motor compartment and busted up the bloewr motor fan,and was making noise and out of balance.i changed the blower motor and runs like a charme

Following the very helpful instructions that I found at PartSelect.com I was able to open the dryer and access the heating element which I suspected was bad. I realized later that I didn't need to open up as much as I did but the job was easy. In the future I would only open the panel below the door to access the element.

Just to make sure that it wasn't a problem with a thermostat or thermal fuse I also checked continuity from the temperature selector knob on the control panel to the heating element. When I verified continuity (zero resistance) I knew that the element was bad. Once I removed it I could see that one of the coils was broken and I should have just checked that first and not bothered opening up the control panel at the top.

Still it was less than an hour of work total. I have some experience with DIY projects but have not worked on appliances before. Thanks for the great site with good instructions and lower costs than the local parts counter.

Followed your online video for disassembly and it was not only educational but actually quite simple. I would recommend that you start the video with," make sure the power cord is disconnected from the power source". I have worked on numerous pieces of large electrical equipment and would strongly suggest this be added. Some people think if it's, "off", it's safe. Your phone staff when ordering was great. We will do business again.

Replaced

It was easier to remove the blower manifold cover, (3 screws) to get at the heater element. Remove the heat shield, disconnect the two wires from the element. There is another screw on the side holding the element in the housing. Remove it and slide the element torward you. I used pliers as it was a snug fit. Replace. Good time to vacuum the whole area.

First, I opened up the front of the dryer and then unscrewed the entire back piece. I assembled the new exhaust piece from the kit. Next, I took out the old straight rear exhaust and then replaced it with the elbow shaped left eshaust from the kit. Lastly, reattache the back and front pieces of the dryer.

I disconnect the power, then the vent pipe. I removed the back panel of the dryer to access the pulley and removed the belt. Replaced the back and put everything back together.