11066752500 Kenmore Dryer - Instructions

Unplug the dryer, take off the rear panel with a nut driver, remove the old heating element (3 screws). remove the thermostat attached to the element, put the thermostat on the new element and install the new element with old screws. re install the back panel with old screws and you are done. Plug it in and it's ready to go!

I watched to replacement video from the website and followed. I did use the tip of a small knife to get the connector to come loose on the old switch. It was a really easy repair.

removed back cover 9 screws , 2 screws on heating element and it pulled out ,3wiers and the new one went in. thermal fuse, was one screw and two wiers and I was done.

After watching your instuctional video I removed the back plate removed old wired and unscrewed the part couldn't have been easier. I have never worked on a dryer in my life and am female :). The hardest part was turning off and unhooking the gas line and again after watching a video on how to do it all went well.

I watched the repair expert on you tube. Went to my dryer and took out the heating element, inspected it, and found a broken element wire. Ordered a new element and since I was in there I also replaced the high limit thermostat. Parts select made it easy and my dryer works great again. Thank you.

Removed top and front of dryer. Removed drum. Removed old rollers from spindles. Installed new rollers and new retainer triangles. Replaced drum. Re-installed front and top.

I made it very difficult. I didn't research the repair. My back is old. It's easier if you just You Tube a video. The top roller you have to take drum completely out. The bottom one, The one that failed for me, you can actually do it without taking anything apart. Access it at bottom back, two holes. I do not have small hands, it would have been easier. Channel Locks inside, 9/16th socket outside. That will loosen main axle. Then use short screwdriver or socket driver on small bracket connected to bottom of unit. Mine had one screw holding it in. Easy bottom fix. I don't really recommend replacing top till it needs it. You can only buy them by the pair too. You will be ready when time comes. I found top roller didn't actually need replacing, did it cause I had it all apart. Don't fix if not broke, right? Trust, BUT, Verify. Smaller hands, would have helped me. All I got.

Used video of PartSelect guy on YouTube to diagnose bad thermal fuse with multimeter. Removed back panel of dryer with nutdriver, removed thermal fuse, found no conductance across terminals. Ordered new part. (It arrived very quickly!) Put in new thermal fuse, replaced back panel. Shortened flexible vent tube so there would be fewer bends. Dryer works now.

I unhooked the gas line, removed the vent hose and then removed the back of the dryer.I replaced the thermal fuse and the cycling thermostat in about 5 minutes. Most of my time was spent vacuuming dust in and around the dryer. The job was easy and my 14 year old dryer works like new.

Unplugged the cable and removed the air-vent hose. Removed the rear panel. Marked and removed the wires from both thermostats. Prior to replacing the new parts I used the vacuum and cleaned all of the excess lint and dust from the dryer. I then installed the new thermostat and fuse. Simple..

David

Having read the instructions and watched the tape, I pried out the remaining catch with a flat screwdriver, read about what the color scheme on the parts wasbout and pushed in the correct part. Voila ! Done in probably two minutes.(By an 82 year old woman!)

The dryer belt was delivered promply, afterwards I lifted the top of the dryer and unscrewed the front panel, so it would lower. Then I watch a 5 minute video and it clearly demonstrated how to install the belt. This was my first time, so it took about 30 minutes.

after replacing my heating element, my dryer still wasn't heating. So i replaced the thermal cut-off unit. from ease of finding the part, to ordering and the instructional videos...this was a no-brainer.thanx guys!!

It could not have been easier, thanks to the video displayed when I ordered the part. It was as easy as removing the back of the dryer, taking out the old fuse and putting in a new old. I have NO repair experience, so little I had to borrow the nutdriver from the maintance man at work. I was more then a little leary to try this repair on my own, but decided it was worth all the money I would save not having to call a repair man for my dryer. Sure glad I did I will continue to attempt more repairs on my own.

i replaced the two sensors in the heating element which were very clear in your diagram and it worked perfectly