Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 11062202101 > Instructions

11062202101 Kenmore Dryer - Instructions

All installation instructions for 11062202101 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 11062202101
1,696-1,710 of 2,372
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Does not turn or tumble

  • Customer: Charles Weston from Pikesville, MD
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Well, to Figure the issue I took the entire thing apart. Actually a lot more than needed. I found the torn belt and ordered it. I did not realize I may need a new belt tensioner which is sold with a wheel for the belt to wrap around and be tensioned by. Actually the original just utilized a rubber c or u shaped design(no wheel) for the belt to slide over. Anyways, instead of ordering and waiting for a new wheeled belt tensioner, I installed new belt with all original parts and working fine. I did oil up the drum rollers to reduce noise. And since I took the whole thing apart I cleaned the lint from every place it could hide. Ps a coke can is said to be helpful to hold the drum up while installing the belt but I found a jug of laundry detergent did better. Totally easy project for someone with no appliance repair history

broken belt that makes the dryer drum go around

  • Customer: kevin from madison, WI
  • Difficulty: Really Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
The broken belt was found when I opened the dryer. The part number was on the belt and a quick online search led me to PartSelect. The part was available, delivered in less than 2 days and there was an online video showing the entire repair in detail.

Dryer will not cut on

  • Customer: Richard from Memphis, TN
  • Difficulty: Really Easy
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
My ground wire in my electrical box was not connected.

My daughter threw a heavy wet comforter into the dryer and the tri-ring sheared off.

  • Customer: Joe from St. Louis, MO
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
I ordered the part(and a backup) and had it in two days. 5 days less than ordering from sears.

Dryer was making lots of noise

  • Customer: clayton from clyde park, MT
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I watched the video on this site and it went exactly as described, fixed it and it sounds like a new dryer. Was going to junk it, glad I didn't!

Auto Dry not advance and 60 minTimed dry advance to end next timed dry cycle

  • Customer: Lance from West Salem, WI
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
PROBLEM: Intermittently, the dryer would not advance on the Auto Dry setting and would stay at max heat continuously, even after 2.5 hours with the clothes dry and very warm. At first, I replaced the CYCLING THERMOSTAT, which DID NOT correct this issue. Then I also found the 60 Minute Timed dry setting would work fine until the end of the cycle and the dryer would stop like it should. Then, I checked back 10-15 minutes later and found the timer had advanced into Fluff Dry Timed cycle with heater on full, but the dryer not moving air. This caused the Thermo-Cut switch (fuse) off to open and the Heater Element would not put out enough heat to dry the clothes. TROUBLESHOOTING: 1- UNPLUG the dryer for all troubleshooting and set the DVM for OHMS ( or use ohm-meter). 2- Both the Cycling Thermostat and High Limit Thermostat checked good at 0 ohms (dryer unplugged). The entire Thermo Cut-off/Thermostat circuit can be checked at the Timer (VERIFY proper wire color with dryer schematic in top console), which also verifies the wires are good and should be 0 ohms without the Heater Element in the circuit. For the Whirlpool WED5300SQ0 dryer, it's the Red and Orange wires at the Timer. 3- If the Heater Element is in the circuit (see schematic for test points), look for between 8-12 ohms for a good Heater Element. For the Whirlpool WED5300SQ0 dryer, it's the Red and White/Black wires at the Timer or across the Heater Element connection. SOLUTION: The Heater Element checked out good at 10 ohms. When the Heater Element was physically removed from the dryer one of the PORCELAIN MOUNTS was BUSTED, which caused the heater element coil to intermittently come in contact with the dryer housing while running/drying clothes, which caused the Timer to not advance on Auto Dry when the Cycling Thermostat Opened and malfunction for the Timed Dry settings. To physically check the Heater Element, just remove the 2 screws and the wires to the High Limit Thermostat can stay hooked up. The Thermo-Cut off kit is easy to install and there is a installation video if there are questions. Just be careful to NOT cut the Heater Element connector on the Jumper wire kit. The spade connector for the heater element is wider than the other side that is cut off for the dual spade connector. The Heater Element is easy to replace as well. If the Thermo-Cutoff Kit is being installed, the new High Limit Thermostat can be mounted to the new Heater Element before it is mounted to the dryer housing, which makes it easier to screw in the self-tapping screws. After this repair was completed, dryer has functioned perfectly after many loads of clothes using all dryer settings.

Heating Element burned out

  • Customer: Robin from Chester, VA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I was pretty sure it was the heating element. I watched two different Youtube videos. Once I cleaned up all of the trash and coins behind the dryer, it was just a matter of removing the screws from the back. I disconnected the wires, replaced the element, and reconnected everything and replaced all of the screws. It works perfectly again!

Replace Drive Belt

  • Customer: William from Marlborough, CT
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
What a pain in the butt to route the belt thru the tensioner! There's room for only one hand in there. The guys who do this for a living must have some secret. My solution was to drill a 3/16 hole thru the side, make a j-hook from 8-32 threaded rod, use that and a wing nut to pre-load the tensioner, route the belt, then slowly back off the wing nut until the belt was tight. It works. . . .

not enough heat

  • Customer: Charles from Bay City, MI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
first I unplugged the dryer. Then I removed the back of the dryer with a 1/4" nut driver. with the back off using the same 1/4" nut driver I removed the one screw that holds the cycling t-stat slowly remove the t-stat and take one wire off at a time and plug it onto the new t-stat once all wires are replaced. place the t-stat back in and secure with the screw. Then put the back of the dryer back on. put the dryer vent hose back on. plug in and away you go. repair done. If that doesn't fix it. Then the next step is probably to check the gas valve coils. That is a little more difficult repair but not to hard.

No heat

  • Customer: Danny from North Chesterfield, VA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Socket set
  • 0 of 0 people found this instruction helpful
Remove back pannel heating element easy to replace. Partselect has the best service ever...

Dryer would start and run but no heat was produced.

  • Customer: andres from yucaipa, CA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Watched several videos online and was suggested that the thermal fuse was bad, so i replaced it but no fix. So i checked the previews Q&A from other costumers and watched the videos on how to replace different parts. I first looked thru the peep hole on the bottom left part of the dryer and saw the igniter glow for about 10 sec every minute but no flame would start. So i replaced the igniter, the flame sensor, and the coils all at once. I know thats not the proper way to troubleshoot something but i was gonna take the drum out and everything so mind as well replace them all. Dryer works like new and dont have to listen to the wife complaint anymore!!!

Broken Belt

  • Customer: gary w from Saint Louis, MO
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Pop off the top , Then one screw holds each side . slide belt around drum and then preload tensioner as per instructions . Simple!

Clothes were not drying, no heat in dryer.

  • Customer: Maxwell from Belen, NM
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
The video is right on. You can't go wrong, and I don't consider myself a handyman at all.

no heat

  • Customer: Tanimu from Mansfield, TX
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I replaced both the Thermal fuse and Cycling Thermostat, both of which cost less than fourty dollars. just removed the back panel, and replaced the parts in less tham a minute. Replaced the back panel. Job done.

Dryer not drying clothes completely

  • Customer: Greg from Gilbert, AZ
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
Super easy repair. Just removed the back panel, took out the old heating element, plugged in the new one and put it back together. I had also replaced the element in a similar Whirlpool dryer in one of my rental properties a few months ago and it was just as easy. Between the two repairs I saved between $200 and $300 in repair labor. PartsSelect always has the parts I need in stock, ships quickly and their installation videos rock. I have also used them for repair parts on microwaves & refrigerators in the past. Excellent vendor. Highly recommended.
All Instructions for the 11062202101
1,696-1,710 of 2,372