Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 11062066100 > Instructions

11062066100 Kenmore Dryer - Instructions

All installation instructions for 11062066100 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 11062066100
346-360 of 516
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Switch broken

  • Customer: Willie from Virginia Beach, VA
  • Difficulty: Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I was impressed with the fast time the part was delivered. The price was good too. The installation video and instructions did not match my dryer but it was helpful to some extent. The video and instructions being different was not ya'll's fault because of the age of the dryer. It took me so long to change the switch was because of the location and design of the switch. I got it though.

no heat when drying clothes

  • Customer: Tracey from Marion, IN
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
  • 0 of 0 people found this instruction helpful
My husband changed the part but part select was very helpful. With their free repair help site it made repairing a breeze! We will use parts select again and again. I did order all the parts we might have needed and only needed one. Now I will return the others.

Dryer Was Running But With No Heat

  • Customer: DEREK from BOCA RATON, FL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I took off the back panel, removed the 2 screws each for the thermostat and cutoff sensor, removed the 2 wires that went to each, screwed in the new parts, reattached the wires, and bingo, the dryer produced heat again. This was my third and final shot at trying to fix this problem as I had already replaced the thermal fuse (was not the issue), and replaced the actual heating coil (apparently wasn't the problem either). However, the dryer is now working better than ever with the new heating coil, drying in about half the time it took before, so I'm glad that was done.

Dryer operating barrel with no heat

  • Customer: Larry from Yelm, WA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Checked the element and switches. Found thermal cut off switch open. Order new switch. Installed switch and vacuumed cabinet. Start and test.

Dryer was throwing a E1 Error

  • Customer: John from Indian land, SC
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Took the back dryer cover off and removed the lint cover all from the back of the dryer then replaces the Thermistor (held with 2 screws).

Door latch was broken

  • Customer: William from Champaign, IL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
This dryer refuses to die and I am happy to keep it that way. Door latch was replaced in less than a minute using this kit. Easiest repair ever.

My dryer had stop working and the terminal block, wires, and dryer plug burnt out

  • Customer: tiffanee from antioch, TN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
I replace the terminal block, wires , and dryer plug I unscrewed the back of the dryer and basically replace was burnt out. I was about to pay 200.00 to have it done but I looked on youtube and seen how easy it was so I just chose the site to order what I needed to be replace and it arrived quickly and more affordable to do it myself. Thanks I hope the was useful.

door would not close

  • Customer: Daniel from Stratford, CT
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Slipped screwdriver on top and bottom of catch and pullef out. Pressed new catch in plact. Job finished.

dryer doesn't complete it's cycle

  • Customer: MICHAEL from PHOENIX, AZ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Removal of the back panel was easy - 9 screws - replaced both the thermistor and the two-terminal thermal fuse - put back panel on - supplied power - tested it - works like a champ.

Washer quit running when lid was closed

  • Customer: Colleen from Indianapolis, IN
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
This repair took me longer because I was just giving it a try - I have no experience, although I tend to be "handy." I'm sure anyone with experience would rate this as "easy" and have taken only a short time. I had to watch the video several times to understand what to do - and the comments were helpful too. My washer is an OLD maytag, so I removed the front of the dash and pulled it forward to access the electronics. My switch had only 2 prongs, so I hooked up to the "lid closed" option on the new switch. It works perfectly now. Very pleased I gave it a try.

dryer would not turn on

  • Customer: Eric from Wallkill, NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
found door switch was ng, replaced however the new part would not fit like the original. I had to use part of the old switch to make it work. It seems as if there was a piece missing from the new replacement part. There was no way it could have worked they way it was recieved. The door switch needs some sort of stand off spacer in order to match the original part. Lucky for me I saved the old part.

Dryer stopped heating

  • Customer: Daniel from Palmyra, VA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Using information found on this site, I was able to quickly locate the two bolts on the lower front panel of the dryer to get at the heating element. Once I removed the panel, I was able to use a multi-meter to determine that the heating element was the issue as the resistance reading was infinite opposed to the expected 10 ohms. When the replacement part arrived, I then re-accessed the heating element to remove it. I removed two bolts from the front deflector to gain access to the heating element (after opening the lower panel) and also removed a third bolt that held the heating element in. Once those were removed, I was able to remove the old heating element which was indeed bad as the wire was broken. I did find that it took a little effort to remove the old heating element. It was quite firmly placed in its location however once I put enough effort into it, it came out quite nicely and the replacement element went in quickly.

Broken door catch

  • Customer: Chuck from Bozeman, MT
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Removed two small screws on door edge, pop out broken part, insert new part, replace screws. Took 2 minutes 18 seconds. Nice to have various door catches in the Kit. This was a repair on a 1979 Whirlpool Dryer. Great price & service!!

Dryer was not heating up

  • Customer: Lynn from Spencer, IN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
I watched a fix it video and than just followed what it said to do. My husband was very impressed and it saved us a lot of money. I had my dryer running in no time. Parts came very quickly after I ordered them. Thank you

old idler pulley was worn out

  • Customer: David J from Eagar, AZ
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Simply slid new idler wheel on then popped thr tri ring on. The belt replacment was the hardest thing which was also easy. I think pulling the dryer away from the wall was the most difficult thing.
All Instructions for the 11062066100
346-360 of 516