Models > 11062042100 > Instructions

11062042100 Kenmore Dryer - Instructions

All Instructions for the 11062042100
301 - 315 of 527
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Lever was broke off
I used you-tube to troubleshoot and repair. Your part store was excellent to deal with. Delivery was prompt and cost was very reasonable. Thanks!
Parts Used:
Dryer Door Switch Actuator Spring/Lever
  • linda from las cruces, NM
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
No heat but functions otherwise
Tested for continuity. The installation video was very good but did not address which wires went to which terminals. Because of polarity, I was uncertain until an appliance repair man told me it didn't matter.
Parts Used:
Thermal Cut-Off Kit
  • David from Barnwell, SC
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers, Wrench set
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
didn't heat up enough
pulled out and installed part
Parts Used:
High Limit Thermostat
  • Lorraine from E Stroudsburg, PA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers, Socket set, Wrench set
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Took to long to dry cloths
It wound up being the design of the dryer vent out of the house, It went straight up 20 ft. Ran new vent. Works fine now.
Parts Used:
Thermal Cut-Off Kit
  • Judy from Naples, GA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Plastic door latch was cracked.
I removed the plastic latch using a screw driver to pry it out. I had to use pliers to completely remove it. Then I snapped the new piece in. It worked perfectly the first time. Very easy repair.
Parts Used:
Door Catch Kit
  • David from Kohler, WI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door latch broken
Repair was straight forward with only two screws to undo. Popped the two sides in and I was done. What was amazing was the lowest cost on parts and the timely delivery.
Parts Used:
Door Catch Kit
  • P from Melbourne Beach, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Couldnt get the dryer to turn on even when i had power.
Very easy to repair remove top of dryer and took out to screws and put switch back in place replaced screws and put top back on. Easy!!
Parts Used:
Dryer Door Switch Actuator Spring/Lever
  • Kevin from Tonica, IL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver, Screw drivers
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door would not latch
I pulled the old latch out of the catch and installed a new one. It just popped into place. The job could not have been easier.
Parts Used:
Door Catch Kit
  • Richard from Millinocket, ME
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
My dryer door would not stay shut.
I removed the old door catch by using a screwdriver to pry it out, then I popped the new door catch in its place and it snapped right in. It took less than 5 minutes to do the whole job.
Parts Used:
Door Catch Kit
  • Michelle from Colby, KS
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
the door switch broke, and I had to pop the lid unscrew the switch and use a clothespin to depress the switch acuator button....not pretty.
same as I described above. However i was amazed when the part showed up the very next day...I was expecting maybe 3 or so days later. I wiil absolutely use PartSelect in the future.
Parts Used:
Dryer Door Switch Actuator Spring/Lever
  • Greg from Phoenixville, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
latch not working on Kenmore dryer
The latch for my Kenmore dryer was only $10 with shipping and just what I
needed. No instructions included, so I googled installation and it was fixed
in less than 3 minutes... YEAH... I am happy!
Parts Used:
Door Catch Kit
  • sally from Houston, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer door wouldn't stay latched shut during cycle
In a matter of moments the dryer that I had grown to despise was back on my good list! I took a pair of pliers and removed the old parts, then inserted the new catch kit. I only about 5 minutes to do AND I love my dryer again!
Parts Used:
Door Catch Kit
  • KRISTIN from DENVER, CO
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
No Heat
Replaced the thermal Cut off
Parts Used:
Thermal Cut-Off Kit
  • Peter from Orlando, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washing machine over 20 years old but still runs strong door switch actuator spring broke original spring was not availible.
drilled a 7/16 diameter hole directly in the center of the two mounting holes filed it square big enough so as the spring tip fits thru now the door closes on the spring which actuates the switch looks and works perfect.
Parts Used:
Dryer Door Switch Actuator Spring/Lever
  • Larry from Elmhurst, IL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Wife pulled bed sheets out of drier and broke door switch actuator
Loosened two screws in back top of drier and pulled forward and up to hinge top of drier and allow access to door switch.Took out broken actuator spring and replaced with new one,snapped lid back in place and put screws back in hinges and job was done.
Parts Used:
Dryer Door Switch Actuator Spring/Lever
  • Ernest from Moundsville, WV
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver, Screw drivers
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 11062042100
301 - 315 of 527
Back to Top